ATMEGA128-16AU Atmel, ATMEGA128-16AU Datasheet - Page 146

• Manufacturer Part Number: ATMEGA128-16AU
• Description: IC AVR MCU 128K 16MHZ 5V 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA128-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: 2-Wire, JTAG, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 4
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AVR MEGA
• No. Of I/o's: 53
• Eeprom Memory Size: 4096Byte
• Ram Memory Size: 4KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Output Compare Unit
146
ATmega128
Depending of the mode of operation used, the counter is cleared, incremented, or dec-
remented at each timer clock (clk
clock source, selected by the clock select bits (CS22:0). When no clock source is
selected (CS22:0 = 0) the timer is stopped. However, the TCNT2 value can be accessed
by the CPU, regardless of whether clk
priority over) all counter clear or count operations.
The counting sequence is determined by the setting of the WGM01 and WGM00 bits
located in the Timer/Counter Control Register (TCCR2). There are close connections
between how the counter behaves (counts) and how waveforms are generated on the
output compare output OC2. For more details about advanced counting sequences and
waveform generation, see “Modes of Operation” on page 149.
The Timer/Counter overflow (TOV2) flag is set according to the mode of operation
selected by the WGM21:0 bits. TOV2 can be used for generating a CPU interrupt.
The 8-bit comparator continuously compares TCNT2 with the Output Compare Register
(OCR2). Whenever TCNT2 equals OCR2, the comparator signals a match. A match will
set the output compare flag (OCF2) at the next timer clock cycle. If enabled (OCIE2 = 1
and global interrupt flag in SREG is set), the output compare flag generates an output
compare interrupt. The OCF2 flag is automatically cleared when the interrupt is exe-
cuted. Alternatively, the OCF2 flag can be cleared by software by writing a logical one to
its I/O bit location. The waveform generator uses the match signal to generate an output
according to operating mode set by the WGM21:0 bits and compare output mode
(COM21:0) bits. The max and bottom signals are used by the waveform generator for
handling the special cases of the extreme values in some modes of operation (see
“Modes of Operation” on page 149). Figure 63 shows a block diagram of the output
compare unit.
clear
clk
top
bottom
Tn
Clear TCNT2 (set all bits to zero).
Timer/Counter clock, referred to as clk
Signalize that TCNT2 has reached maximum value.
Signalize that TCNT2 has reached minimum value (zero).
T2
). clk
T2
T2
is present or not. A CPU write overrides (has
can be generated from an external or internal
T0
in the following.
2467M–AVR–11/04