LPC1759FBD80,551 NXP Semiconductors, LPC1759FBD80,551 Datasheet - Page 332

• Manufacturer Part Number: LPC1759FBD80,551
• Description: IC ARM CORTEX MCU 512K 80-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1759FBD80,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 80-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 120MHz
• Connectivity: CAN, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 52
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 6x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC17
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: Ethernet, USB, OTG, CAN
• Maximum Clock Frequency: 120 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 6 Channel
• On-chip Dac: 10 bit
• Package: 80LQFP
• Device Core: ARM Cortex M3
• Family Name: LPC17xx
• Maximum Speed: 120 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4968; 935290523551

NXP Semiconductors
Table 304: Auto-baud Control Register (U1ACR - address 0x4001 0020) bit description
UM10360
User manual
Bit
2
7:3
8
9
31:10 -
Symbol
AutoRestart
-
ABEOIntClr
ABTOIntClr
15.4.14 Auto-baud
Value Description
0
1
NA
0
1
0
1
NA
The UART1 auto-baud function can be used to measure the incoming baud-rate based on
the “AT” protocol (Hayes command). If enabled the auto-baud feature will measure the bit
time of the receive data stream and set the divisor latch registers U1DLM and U1DLL
accordingly.
Remark: the fractional rate divider is not connected during auto-baud operations, and
therefore should not be used when the auto-baud feature is needed.
Auto-baud is started by setting the U1ACR Start bit. Auto-baud can be stopped by clearing
the U1ACR Start bit. The Start bit will clear once auto-baud has finished and reading the
bit will return the status of auto-baud (pending/finished).
Two auto-baud measuring modes are available which can be selected by the U1ACR
Mode bit. In mode 0 the baud-rate is measured on two subsequent falling edges of the
UART1 Rx pin (the falling edge of the start bit and the falling edge of the least significant
bit). In mode 1 the baud-rate is measured between the falling edge and the subsequent
rising edge of the UART1 Rx pin (the length of the start bit).
The U1ACR AutoRestart bit can be used to automatically restart baud-rate measurement
if a time-out occurs (the rate measurement counter overflows). If this bit is set the rate
measurement will restart at the next falling edge of the UART1 Rx pin.
The auto-baud function can generate two interrupts.
The auto-baud interrupts have to be cleared by setting the corresponding U1ACR
ABTOIntClr and ABEOIntEn bits.
Typically the fractional baud-rate generator is disabled (DIVADDVAL = 0) during
auto-baud. However, if the fractional baud-rate generator is enabled (DIVADDVAL > 0), it
is going to impact the measuring of UART1 Rx pin baud-rate, but the value of the U1FDR
•
•
The U1IIR ABTOInt interrupt will get set if the interrupt is enabled (U1IER ABToIntEn
is set and the auto-baud rate measurement counter overflows).
The U1IIR ABEOInt interrupt will get set if the interrupt is enabled (U1IER ABEOIntEn
is set and the auto-baud has completed successfully).
No restart
Restart in case of time-out (counter restarts at next UART1 Rx falling edge)
Reserved, user software should not write ones to reserved bits. The value read
from a reserved bit is not defined.
End of auto-baud interrupt clear bit (write-only accessible).
Writing a 0 has no impact.
Writing a 1 will clear the corresponding interrupt in the U1IIR.
Auto-baud time-out interrupt clear bit (write-only accessible).
Writing a 0 has no impact.
Writing a 1 will clear the corresponding interrupt in the U1IIR.
Reserved, user software should not write ones to reserved bits. The value read
from a reserved bit is not defined.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
Chapter 15: LPC17xx UART1
UM10360
© NXP B.V. 2010. All rights reserved.
0
0
Reset value
0
0
0
0
332 of 840