SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 936

• Manufacturer Part Number: SAM9M10
• Manufacturer: Atmel Corporation

Specifications of SAM9M10

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: Yes
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

936
SAM9M10
• For Trigger Counter at 1:
1. Close the switches on the inputs X
2. Convert Channel X
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 2.
• For Trigger Counter at 2:
1. Close the switches on the inputs X
2. Convert Channel Y
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 3.
• For Trigger Counter at 3:
1. Close the switches on the inputs Y
2. Convert Channel Y
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 4.
• For Trigger Counter at 4:
1. Close the switches on the inputs Y
2. Convert Channel Y
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 5.
• For Trigger Counter at 5:
1. Close the switches on the inputs Y
2. Convert Channel X
3. If Channel 4 to Channel 7 are enabled, convert Channels and store result in the corre-
4. Set Trigger Counter to 6.
• For Trigger Counter between 6 and (2
1. Increment Trigger Counter.
2. If Trigger Counter equals (2
result in TSADCC_CDR0 (and also in TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
tion result in TSADCC_CDR1 (and also in TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
sponding TSADCC_CDRx and TSADCC_LCDR.
result in TSADCC_CDR2 (and also in TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
result in TSADCC_CDR3 (and also in TSADCC_LCDR if PDCEN is enabled).
sponding TSADCC_CDRx and TSADCC_LCDR.
P
P
P
P
M
, subtract TSADCC_CDR1 from the result and store the subtraction
, subtract TSADCC_CDR3 from the result and store the subtraction
, subtract TSADCC_CDR3 from the result and store the subtraction
,, subtract TSADCC_CDR1 from the result and store the subtrac-
and store the result in TSADCC_CDR3.
TSFREQ+1
P
P
P
P
P
TSFREQ+1
), then set Trigger Counter to 0.
and Y
and Y
and Y
and X
and X
M
M
M
M
M
):
during the Sample and Hold Time.
during the Sample and Hold Time.
during the Sample and Hold Time
during the Sample and Hold Time.
during the Sample and Hold Time.
6355D–ATARM–7-Sep-11