SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 1384

• Manufacturer Part Number: SAM9M10
• Manufacturer: Atmel Corporation

Specifications of SAM9M10

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: Yes
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

1384
Doc. Rev
6355C
SAM9M10
Comments
Introduction
Product Line/Product naming convention changed - AT91SAM ARM-based MPU / SAM9M10
Section 5.1 “Power
GNDIOP, GNDBU, GNDOSC, GNDUTMI.
Reorganized text describing GND association to power supply pins
Clock Generator
Figure 25-2
DDRSDRC
“DDRSDRC Timing 1 Parameter Register”
255”.
HSMCI
Section 35.1
PMC
Section 26.4 “Processor Clock
RTC
Section 14.6 “Real Time Clock (RTC) User
SPI
WDRBT variable and conditional text shown, now appearing in
TRNG
KEY bitfield added to
TWI
Section 32.2 “Embedded
UDPHS
Figure 38-3 “Board
UHPHS
Figure 37-4 “Board Schematic to Interface UHP High-speed Device
GNDUTMI.
Electrical Characteristics
Table 47-23, “Analog
In the footnote below
In the figure below, GNDPLL changed to GNDOSC.
‘pF’ value has to be written this way: ‘Pf’ and ‘pf’ removed.
Errata
Section 50.1.3.1 “ECC: Computation with a 1 clock cycle long NRD/NWE
ECC.
Section 50.1.8.1 “UHPHS: Packet Loss Issue in the UTMI Transceivers”
Section 50.1.9.1 “UHPHS/UDPHS: USB does not start after
choices in “Workaround”.
and
“Description”,
Figure
Schematic”, GND changed to GNDUTMI.
Supplies”, replaced ground pin names by GNDIOM, GNDCORE, GNDANA,
Table 47-7, “Main Oscillator
“TRNG Control Register”
Inputs”, ’ Input Impedance’ changed in ‘Input Source Impedance’.
25-5, GND changed to GNDOSC.
Characteristics”, PDC feature removed from the list.
SDIO V1.1 changed to SDIO V2.0
Controller”, 2nd and 3rd paragraphs edited.
Interface”, typo in section title fixed.
,TXSNR field, “Number of cycles is between 0 and
Characteristics”, gnd changed to gndosc.
.
power-up”, a clarifying “Or” added to
Section 28.8.2 “SPI Mode Register”
Controller”, GND changed to
added.
pulse”, HECC changed to
6355D–ATARM–7-Sep-11
Change
Request
Ref.
rfo
7332
rfo
7332
7462
7384
7392
7569
7508
7531
7266
7332
7332
7519
7332
rfo
7384
7595
7352