SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 502

• Manufacturer Part Number: SAM9M10
• Manufacturer: Atmel Corporation

Specifications of SAM9M10

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: Yes
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 31-14. Asynchronous Start Bit Detection
Figure 31-15. Preamble Pattern Mismatch
Figure 31-16. Manchester Error Flag
502
SAM9M10
Manchester
encoded
Manchester
Sampling
Manchester
encoded
encoded
data
Clock
(16 x)
data
data
The receiver is activated and starts Preamble and Frame Delimiter detection, sampling the data
at one quarter and then three quarters. If a valid preamble pattern or start frame delimiter is
detected, the receiver continues decoding with the same synchronization. If the stream does not
match a valid pattern or a valid start frame delimiter, the receiver re-synchronizes on the next
valid edge.The minimum time threshold to estimate the bit value is three quarters of a bit time.
If a valid preamble (if used) followed with a valid start frame delimiter is detected, the incoming
stream is decoded into NRZ data and passed to USART for processing.
Manchester pattern mismatch. When incoming data stream is passed to the USART, the
receiver is also able to detect Manchester code violation. A code violation is a lack of transition
in the middle of a bit cell. In this case, MANE flag in US_CSR register is raised. It is cleared by
writing the Control Register (US_CR) with the RSTSTA bit at 1. See
ple of Manchester error detection during data phase.
When the start frame delimiter is a sync pattern (ONEBIT field at 0), both command and data
delimiter are supported. If a valid sync is detected, the received character is written as RXCHR
sampling points
Txd
Txd
Txd
1
Manchester coding error
2
Preamble Length
3
Preamble Mismatch
4
is set to 4
Preamble Length is set to 8
Detection
Start
and Start Frame Delimiter
Preamble subpacket
were successfully
Preamble Mismatch
SFD
decoded
invalid pattern
Entering USART character area
Elementary character bit time
SFD
Coding Error
Manchester
Figure 31-16
detected
DATA
Figure 31-15
6355D–ATARM–7-Sep-11
for an exam-
illustrates