SAM9M10 Atmel Corporation, SAM9M10 Datasheet - Page 817

• Manufacturer Part Number: SAM9M10
• Manufacturer: Atmel Corporation

Specifications of SAM9M10

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: Yes
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

6355D–ATARM–7-Sep-11
To configure the endpoints:
Note: For control endpoints the direction has no effect.
Control endpoints can generate interrupts and use only 1 bank.
All endpoints (except endpoint 0) can be configured either as Bulk, Interrupt or Isochronous. See
Table 38-1. UDPHS Endpoint
The maximum packet size they can accept corresponds to the maximum endpoint size.
Note: The endpoint size of 1024 is reserved for isochronous endpoints.
The size of the DPRAM is
required by the active endpoints must not exceed the size of the DPRAM.
SIZE_DPRAM = SIZE _EPT0
If a user tries to configure endpoints with a size the sum of which is greater than the DPRAM,
then the EPT_MAPD is not set.
The application has access to the physical block of DPR reserved for the endpoint through a
KB logical address space.
The physical block of DPR allocated for the endpoint is remapped all along the
address space. The application can write a
• Fill the configuration register (UDPHS_EPTCFG) with the endpoint size, direction (IN or
• Fill the number of transactions (NB_TRANS) for isochronous endpoints.
• Verify that the EPT_MAPD flag is set. This flag is set if the endpoint size and the number of
• Configure control flags of the endpoint and enable it in UDPHS_EPTCTLENBx according to
OUT), type (CTRL, Bulk, IT, ISO) and the number of banks.
banks are correct compared to the FIFO maximum capacity and the maximum number of
allowed banks.
“UDPHS Endpoint Control Register” on page
+ NB_BANK_EPT1 x SIZE_EPT1
+ NB_BANK_EPT2 x SIZE_EPT2
+ NB_BANK_EPT3 x SIZE_EPT3
+ NB_BANK_EPT4 x SIZE_EPT4
+ NB_BANK_EPT5 x SIZE_EPT5
+ NB_BANK_EPT6 x SIZE_EPT6
+... (refer to
38.6.11 UDPHS Endpoint Configuration
4
KB. The DPR is shared by all active endpoints. The memory size
Description.
64
KB buffer linearly.
862.
Register)
SAM9M10
64
KB logical
817
64