AT91SAM9263B-CU Atmel, AT91SAM9263B-CU Datasheet - Page 862

• Manufacturer Part Number: AT91SAM9263B-CU
• Description: IC ARM9 MCU 200 MHZ 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9263B-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: CAN, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 96 KB
• Interface Type: 2-Wire, EBI, I2S, MCI, SPI, USART
• Maximum Clock Frequency: 200 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9263-EK
• Minimum Operating Temperature: - 40 C
• Package: 324TFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 200 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 160
• Ram Memory Size: 96KB
• Cpu Speed: 240MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• For Use With: AT91SAM9263-EK - KIT EVAL FOR AT91SAM9263AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q3735625

43.4
Figure 43-2. Board Schematic to Interface Device Peripheral
43.4.1
43.4.2
862
Typical Connection
AT91SAM9263
USB Device Transceiver
VBUS Monitoring
PIO
DDM
DDP
5V Bus Monitoring
The USB device transceiver is embedded in the product. A few discrete components are
required as follows:
VBUS monitoring is required to detect host connection. VBUS monitoring is done using a stan-
dard PIO with internal pullup disabled. When the host is switched off, it should be considered as
a disconnect, the pullup must be disabled in order to prevent powering the host through the pull-
up resistor.
When the host is disconnected and the transceiver is enabled, then DDP and DDM are floating.
This may lead to over consumption. A solution is to connect 330 KΩ pulldowns on DP and DM.
These pulldowns do not alter DDP and DDM signal integrity.
A termination serial resistor must be connected to DP and DM. The resistor value is defined in
the electrical specification of the product (R
• the application detects all device states as defined in chapter 9 of the USB specification;
• to reduce power consumption the host is disconnected
• for line termination.
– VBUS monitoring
47 K
27 K
R
R
EXT
EXT
330 K
EXT
).
330 K
2
3
Connector
Type B
1
4
6249H–ATARM–27-Jul-09