AT91SAM9263B-CU Atmel, AT91SAM9263B-CU Datasheet - Page 1077

• Manufacturer Part Number: AT91SAM9263B-CU
• Description: IC ARM9 MCU 200 MHZ 324-TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9263B-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: CAN, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 96 KB
• Interface Type: 2-Wire, EBI, I2S, MCI, SPI, USART
• Maximum Clock Frequency: 200 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9263-EK
• Minimum Operating Temperature: - 40 C
• Package: 324TFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 200 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Controller Family/series: AT91SAM9xxx
• No. Of I/o's: 160
• Ram Memory Size: 96KB
• Cpu Speed: 240MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• For Use With: AT91SAM9263-EK - KIT EVAL FOR AT91SAM9263AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q3735625

50.3.9.2
50.3.9.3
50.3.9.4
50.3.9.5
50.3.10
50.3.10.1
50.3.11
50.3.11.1
6249H–ATARM–27-Jul-09
NTRST
Reset Controller (RSTC)
SDIO interrupt does not work with slots other than A
Data Timeout Error Flag
Data Write Operation and Number of Bytes
Flag Reset is not correct in half duplex mode
NTRST: Device does not boot correctly due to power-up sequencing issue
RSTC: ERSTL Default Value is 1
If there is a 1-bit data bus width on other slots than Slot A, the SDIO interrupt cannot be cap-
tured. The sample is made on the wrong data line.
None
As the data Timeout error flag checking the Naac timing cannot rise, the MCI can be stalled wait-
ing indefinitely the Data start bit.
A STOP command must be sent with a software timeout.
The Data Write operation with a number of bytes less than 12 is impossible.
The PDC counters must always be equal to 12 bytes for data transfers lower than 12 bytes. The
BLKLEN or BCNT field are used to specify the real count number.
In half duplex mode, the reset of the flags ENDRX, RXBUFF, ENDTX and TXBUFE can be
incorrect.
These flags are reset correctly after a PDC channel enable.
Enable the interrupts related to ENDRX, ENDTX, RXBUFF and TXBUFE only after enabling the
PDC channel by writing PDC_TXTEN or PDC_RXTEN.
The NTRST signal is powered by VDDIOP power supply (3.3V) and the ARM processor is pow-
ered by VDDCORE power supply (1.2V).
During the power-up sequence, if VDDIOP power supply is not established whereas the
VDDCORE Power On Reset output is released, the NTRST signal is not correctly asserted. This
leads to a bad reset of the Embedded Trace Macrocell (ETM9). The ARM processor then enters
debug state and the device does not boot correctly.
The default value of ERSTL field in RSTC_MR register has been changed from 0x0 to 0x1. This
means that the NRST line rises 4 cycles after backup_nreset
1. Connect NTRST pin to NRST pin to ensure that a correct powering sequence takes
2. Connect NTRST to GND if no debug capabilities are required.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
place in all cases.
AT91SAM9263
1077