ATMEGA64M1-15MZ Atmel, ATMEGA64M1-15MZ Datasheet - Page 224

• Manufacturer Part Number: ATMEGA64M1-15MZ
• Description: MCU AVR 64KB FLASH 3PSC 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64M1-15MZ

• Package / Case: 32-VQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Eeprom Size: 2K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Connectivity: CAN, LIN, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATADAPCAN01
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of I /o: -
• Lead Free Status / Rohs Status: Details

17.6.2
224
Atmel ATmega16/32/64/M1/C1
LIN Status and Interrupt Register - LINSIR
• Bit 3 - LENA: Enable
• Bit 2:0 - LCMD[2..0]: Command and mode
• Bits 7:5 - LIDST[2:0]: Identifier Status
• Bit 4 - LBUSY: Busy Signal
Bit
Read/Write
Initial Value
b. UART mode (default = 00):
– 01 = No CRC, no Time out (listen mode “off”),
– 10 = No Frame_Time_Out (listen mode “off” & CRC “on”),
– 11 = Listening mode (CRC “on” & Frame_Time_Out “on”).
– 00 = 8-bit, no parity (listen mode “off”),
– 01 = 8-bit, even parity (listen mode “off”),
– 10 = 8-bit, odd parity (listen mode “off”),
– 11 = Listening mode, 8-bit, no parity.
– 0 = Disable (both LIN and UART modes),
– 1 = Enable (both LIN and UART modes).
–000 = LIN Rx Header - LIN abort,
– 001 = LIN Tx Header,
– 010 = LIN Rx Response,
– 011 = LIN Tx Response,
– 100 = UART Rx & Tx Byte disable,
– 11x = UART Rx Byte enable,
– 1x1 = UART Tx Byte enable.
– 0xx = no specific identifier,
– 100 = Identifier 60 (0x3C),
– 101 = Identifier 61 (0x3D),
– 110 = Identifier 62 (0x3E),
– 111 = Identifier 63 (0x3F).
– 0 = Not busy,
– 1 = Busy (receiving or transmitting).
The command is only available if LENA is set.
LIDST2
R
7
0
LIDST1
R
6
0
LIDST0
R
5
0
LBUSY
R
4
0
R/W
LERR
3
0
one
R/W
LIDOK
2
0
one
LTXOK
R/W
1
0
one
LRXOK
R/W
0
0
7647G–AVR–09/11
one
LINSIR