ATMEGA64M1-15MZ Atmel, ATMEGA64M1-15MZ Datasheet - Page 189

• Manufacturer Part Number: ATMEGA64M1-15MZ
• Description: MCU AVR 64KB FLASH 3PSC 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64M1-15MZ

• Package / Case: 32-VQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Eeprom Size: 2K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Connectivity: CAN, LIN, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATADAPCAN01
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of I /o: -
• Lead Free Status / Rohs Status: Details

16.10.3
7647G–AVR–09/11
CAN General Interrupt Register - CANGIT
• Bit 2 – ENFG: Enable Flag
This flag does not generate an interrupt.
• Bit 1 – BOFF: Bus Off Mode
BOFF gives the information of the state of the CAN channel. Only entering in bus off mode
generates the BOFFIT interrupt.
• Bit 0 – ERRP: Error Passive Mode
ERRP gives the information of the state of the CAN channel. This flag does not generate an
interrupt.
• Bit 7 – CANIT: General Interrupt Flag
This is a read only bit.
• Bit 6 – BOFFIT: Bus Off Interrupt Flag
Writing a logical one resets this interrupt flag. BOFFIT flag is only set when the CAN enters in
bus off mode (coming from error passive mode).
• Bit 5 – OVRTIM: Overrun CAN Timer
Writing a logical one resets this interrupt flag. Entering in CAN timer overrun interrupt handler
also reset this interrupt flag
Initial Value
Read/Write
– 1 - receiver busy: set by hardware as long as a frame is received or monitored.
– 0 - CAN controller disable: because an enable/standby command is not
– 1 - CAN controller enable.
– 0 - no bus off mode.
– 1 - bus off mode.
– 0 - no error passive mode.
– 1 - error passive mode.
Bit
– 0 - no interrupt.
– 1 - CAN interrupt: image of all the CAN controller interrupts except for OVRTIM
– 0 - no interrupt.
– 1 - bus off interrupt when the CAN enters in bus off mode.
– 0 - no interrupt.
– 1 - CAN timer overrun interrupt: set when the CAN timer switches from 0xFFFF to 0.
immediately effective, this status gives the true state of the chosen mode.
interrupt. This bit can be used for polling method.
CANIT
R
7
0
BOFFIT
R/W
6
0
OVRTIM
R/W
5
0
Atmel ATmega16/32/64/M1/C1
BXOK
R/W
4
0
SERG
R/W
3
0
CERG
R/W
2
0
FERG
R/W
1
0
AERG
R/W
0
0
CANGIT
189