ATMEGA64M1-15MZ Atmel, ATMEGA64M1-15MZ Datasheet - Page 117

• Manufacturer Part Number: ATMEGA64M1-15MZ
• Description: MCU AVR 64KB FLASH 3PSC 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64M1-15MZ

• Package / Case: 32-VQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Eeprom Size: 2K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Connectivity: CAN, LIN, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATADAPCAN01
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of I /o: -
• Lead Free Status / Rohs Status: Details

13.6.1
7647G–AVR–09/11
Force Output Compare
Figure 13-4. Output Compare Unit, Block Diagram
The OCRnx Register is double buffered when using any of the twelve Pulse Width Modulation
(PWM) modes. For the Normal and Clear Timer on Compare (CTC) modes of operation, the
double buffering is disabled. The double buffering synchronizes the update of the OCRnx
Compare Register to either TOP or BOTTOM of the counting sequence. The synchronization
prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the out-
put glitch-free.
The OCRnx Register access may seem complex, but this is not case. When the double buffer-
ing is enabled, the CPU has access to the OCRnx Buffer Register, and if double buffering is
disabled the CPU will access the OCRnx directly. The content of the OCR1x (Buffer or Com-
pare) Register is only changed by a write operation (the Timer/Counter does not update this
register automatically as the TCNT1 and ICR1 Register). Therefore OCR1x is not read via the
high byte temporary register (TEMP). However, it is a good practice to read the low byte first
as when accessing other 16-bit registers. Writing the OCRnx Registers must be done via the
TEMP Register since the compare of all 16 bits is done continuously. The high byte (OCRnxH)
has to be written first. When the high byte I/O location is written by the CPU, the TEMP Regis-
ter will be updated by the value written. Then when the low byte (OCRnxL) is written to the
lower eight bits, the high byte will be copied into the upper 8-bits of either the OCRnx buffer or
OCRnx Compare Register in the same system clock cycle.
For more information of how to access the 16-bit registers refer to
on page
In non-PWM Waveform Generation modes, the match output of the comparator can be forced
by writing a one to the Force Output Compare (FOCnx) bit. Forcing compare match will not set
the OCFnx Flag or reload/clear the timer, but the OCnx pin will be updated as if a real com-
pare match had occurred (the COMn1:0 bits settings define whether the OCnx pin is set,
cleared or toggled).
109.
OCRnxH Buf. (8-bit)
OCRnxH (8-bit)
BOTTOM
OCRnx Buffer (16-bit Register)
TEMP (8-bit)
TOP
OCRnx (16-bit Register)
Atmel ATmega16/32/64/M1/C1
OCRnxL Buf. (8-bit)
OCRnxL (8-bit)
DATA BUS
Waveform Generator
WGMn3:0
=
(16-bit Comparator )
(8-bit)
COMnx1:0
TCNTnH (8-bit)
OCFnx (Int.Req.)
TCNTn (16-bit Counter)
“Accessing 16-bit Registers”
TCNTnL (8-bit)
OCnx
117