DF2117VLP20V Renesas Electronics America, DF2117VLP20V Datasheet - Page 21

• Manufacturer Part Number: DF2117VLP20V
• Description: IC H8S/2117 MCU FLASH 145TFLGA
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2100r

Specifications of DF2117VLP20V

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: FIFO, I²C, LPC, SCI, SmartCard
• Peripherals: POR, PWM, WDT
• Number Of I /o: 112
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 145-TFLGA
• For Use With: HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)3DK2166 - DEV EVAL KIT H8S/2166
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Item
22.2 Mode Transition Diagram
22.5 Programming/Erasing
Interface
22.7.1 Programming/Erasing
Interface Registers
(5) Flash MAT Select Register
(FMATS)
Page Revision (See Manual for Details)
678
680
689
Description added
• The user boot Mat can be programmed or erased
• In boot mode, the user MAT and user boot MAT are
• In user boot mode, boot operation of the optional
Description amended
The procedure program for user program mode/user
boot mode is made by the user. Figure 22.5 shows the
procedure for creating the procedure program. For
details, see section 22.8.2, User Program Mode/section
22.8.3, User Boot Mode.
Table amended
Bit
7
6
5
4
3
2
1
0
only in boot mode and programmer mode.
totally erased. Then, the user MAT or user boot
MAT can be programmed by means of commands.
Note that the contents of the MAT cannot be read
until this state.
Boot mode can be used for programming only the
user boot MAT and then programming the user MAT
in user boot mode. Another way is to program only
the user MAT since user boot mode is not used.
interface can be performed with mode pin settings
different from those in user program mode.
Bit Name
MS7
MS6
MS5
MS4
MS3
MS2
MS1
MS0
Initial
Value
0/1*
0
0/1*
0
0/1*
0
0/1*
0
1
1
1
1
R/W
R/W*
R/W*
R/W*
R/W*
R/W*
R/W*
R/W*
R/W*
Rev. 3.00 Sep. 28, 2009 Page xix of xliv
2
2
2
2
2
2
2
2
Description
MAT Select
The user MAT is selected when a value other than
H'AA is written, and the user boot MAT is selected
when H'AA is written. The MAT is switched by writing a
value in FMATS. To switch the MAT, make sure to
follow section 22.10, Switching between User MAT and
User Boot MAT. (The user boot MAT cannot be
programmed in user program mode even if the user
boot MAT is selected by FMATS. The user boot MAT
must be programmed in boot mode or programmer
mode.)
H'AA: User boot MAT is selected (user MAT is selected
H'00: Initial value when initiated in a mode other than
[Programmable condition]
Execution state in the on-chip RAM
when the value of these bits is other than H'AA).
Initial value when initiated in user boot mode.
user boot mode (user MAT is selected).
REJ09B0350-0300