MOD5234-100IR NetBurner Inc, MOD5234-100IR Datasheet - Page 217
MOD5234-100IR
Manufacturer Part Number
MOD5234-100IR
Description
MOD5234 10/100 ETHERNET MODULE
Manufacturer
NetBurner Inc
Type
Controllers & Processorsr
Datasheets
1.MOD5272-100IR.pdf
(3 pages)
2.MOD5234-100IR.pdf
(4 pages)
3.MOD5234-100IR.pdf
(754 pages)
Specifications of MOD5234-100IR
Interface
I²C, SPI, UART
Voltage - Supply
2.5V
Mounting Type
Surface Mount
Package / Case
Module
Product
Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Format
-
Baud Rates
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
Q4483564
- Current page: 217 of 754
- Download datasheet (13Mb)
11.2.1.4 Core Watchdog Control Register (CWCR)
The core watchdog timer prevents system lockup if the software becomes trapped in a loop with
no controlled exit. The core watchdog timer can be enabled or disabled through CWCR[CWE].
By default it is disabled. If enabled, the watchdog timer requires the periodic execution of a core
watchdog servicing sequence. If this periodic servicing action does not occur, the timer times out,
resulting in a watchdog timer interrupt. If the timer times out and the core watchdog transfer
acknowledge enable bit (CWCR[CWTA]) is set, a watchdog timer interrupt is asserted. If a core
watchdog timer interrupt acknowledge cycle has not occurred after another timeout, CWT TA is
asserted in an attempt to allow the interrupt acknowledge cycle to proceed by terminating the bus
cycle. The setting of CWCR[CWTAVAL] indicates that the watchdog timer TA was asserted.
To prevent the core watchdog timer from interrupting, the CWSR must be serviced by performing
the following sequence:
Both writes must occur in order before the time-out, but any number of instructions can be
executed between the two writes. This order allows interrupts and exceptions to occur, if
necessary, between the two writes. Caution should be exercised when changing CWCR values
after the software watchdog timer has been enabled with the setting of CWCR[CWE], because it
is difficult to determine the state of the core watchdog timer while it is running. The countdown
value is constantly compared with the time-out period specified by CWCR[CWT]. The following
steps must be taken to change CWT:
The CWCR controls the software watchdog timer, time-out periods, and software watchdog timer
transfer acknowledge. The register can be read at any time, but can be written only if the CWT is
not pending. At system reset, the software watchdog timer is disabled.
Freescale Semiconductor
1. Write 0x55 to CWSR.
2. Write 0xAA to the CWSR.
1. Disable the core watchdog timer by clearing CWCR[CWE].
2. Reset the counter by writing 0x55 and then 0xAA to CWSR.
3. Update CWCR[CWT].
4. Re-enable the core watchdog timer by setting CWCR[CWE]. This step can be performed
in step 3.
Address
Figure 11-4. Core Watchdog Control Register (CWCR)
Reset
W
R
CWE
0
7
CWRI
MCF5235 Reference Manual, Rev. 2
0
6
0
5
IPSBAR + 0x011
CWT
0
4
0
3
CWTA CWTAV
2
0
AL
0
1
Memory Map/Register Definition
CWTIC
0
0
11-7
Related parts for MOD5234-100IR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 MODULE
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 Core Module Development Kit
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
BOARD SERIAL-ETHERNET 512K FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5282
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet Modules & Development Tools 32 Bit 66MHz 40 Pin DIP Industrial Temp
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet ICs 32bit 147MHz CAN-to- Ethnt Device IndTemp
Manufacturer:
NetBurner Inc
Datasheet: