HD64F2218UTF24 Renesas Electronics America, HD64F2218UTF24 Datasheet - Page 127

IC H8S MCU FLASH 128K 100-TQFP

HD64F2218UTF24

Manufacturer Part Number
HD64F2218UTF24
Description
IC H8S MCU FLASH 128K 100-TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2200r
Datasheets

Specifications of HD64F2218UTF24

Core Processor
H8S/2000
Core Size
16-Bit
Speed
24MHz
Connectivity
SCI, SmartCard, USB
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
69
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
For Use With
3DK2218-SS - KIT DEV H8S/2218 WINDOWS SIDESHW
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HD64F2218UTF24
Manufacturer:
RENESAS
Quantity:
14
Part Number:
HD64F2218UTF24V
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
3.1
This LSI supports four operating modes (modes 4 to 7). These modes enable selection of the CPU
operating mode, enabling/disabling of on-chip ROM, and the initial bus width setting, by setting
the mode pins (MD2 to MD0) as show in table 3.1. Modes 4 to 6 are external extended modes that
allow access to the external memory and peripheral devices. In external extended mode, 8-bit or
16-bit address space can be set for each area depending on the bus controller setting after program
execution starts. If 16-bit access is selected for any one area, 16-bit bus mode is set; if 8-bit access
is selected for all areas, 8-bit bus mode is set. In mode 7, the external address space cannot be
used. Do not change the mode pin settings during operation. Only mode 7 is available in the
H8S/2212 Group.
Table 3.1
Note: When using the E6000 emulator:
MCU
Operating
Mode
4
5
6
7
Operating Mode Selection
MD2 MD1 MD0
1
1
1
1
Mode 7 is not available in the H8S/2218 Group. (The E6000 emulator does not support
mode 7.)
Note following restrictions to use the RTC and USB in mode 6.
Specify PFCR so that A9 and A8 are output on the PB1 and PB0 pins.
Set H'FF in PCDDR so that A7 to A0 are output on the PC7 to PC0 pins.
MCU Operating Mode Selection
0
0
1
1
Section 3 MCU Operating Modes
0
1
0
1
CPU Operating
Mode
Advanced mode
Advanced mode
Advanced mode
Advanced mode
Description
On-chip ROM
disabled, extended
mode
On-chip ROM
disabled, extended
mode
On-chip ROM
enabled, extended
mode
Single-chip mode
Rev.7.00 Dec. 24, 2008 Page 71 of 698
On-chip
ROM
Disabled
Disabled
Enabled
Enabled
Initial Value
16 bits
8 bits
8 bits
External Data Bus
REJ09B0074-0700
Maximum
Value
16 bits
16 bits
16 bits

Related parts for HD64F2218UTF24