s5u1c33000c Epson Electronics America, Inc., s5u1c33000c Datasheet - Page 478

• Manufacturer Part Number: s5u1c33000c
• Description: Cmos 32-bit Single Chip Microcomputer S5u1c33000c Manual
• Manufacturer: Epson Electronics America, Inc.

CHAPTER 16: DEBUGGER
16.13 Status/Error/Warning Messages
This section describes the messages that are displayed in the [Command] window by the debugger.
16.13.1 Status Messages
When the target program breaks, the db33 displays one of the following messages to indicate the cause of the
break immediately before it stands by for a command input.
16.13.2 Error Messages
462
Break by software PC break.
Break by hardware PC break.
Break by hardware PC break 2.
Break by temporary break.
Break by data break.
Break by read memory.
Break by write memory.
Break by sequential break.
Break by key break, xxxx.
Break by accessing no map area.
Break by writing ROM area.
Break by out of SP area.
Break by external break.
Break by illegal instruction.
Break by MEM33 bus break.
Break by MEM33 ce break.
Break by MEM33 area break.
Break by MEM33 map break.
Address is in no map area.
Address is not 2 byte boundary.
Address mask range (0-0xFFFFFF).
Address range (0-0xFFFFFFF).
address1 > address2.
Already exist input address.
Argument1 range (0-0xFFFFFFF).
Argument2 range (0-0xFFFFFFF).
Argument3 range (0-0xFFFFFFF).
Break number (1-16).
Break number (1-8).
Cannot add symbol any more.
Cannot allocate memory.
Cannot close file.
Cannot compare data, file open failure, xxx.srf. xxx.srf cannot be opened.
Cannot get file status.
Cannot get input, please check the system.
Cannot get memory.
Cannot load data, file open failure.
Cannot load data, file read failure.
Cannot load data, memory allocation failure.
Cannot load data, please check SRF33 file.
Cannot load debug information,
debug information is wrong.
Cannot load debug information,
file open failure.
Cannot load debug information,
file read failure.
Cannot load debug information,
memory allocation failure.
Message
Error message
Break caused by software PC breakpoint
Break caused by hardware PC breakpoint
Break caused by hardware PC breakpoint
Break caused by temporary breakpoint
Break caused by data break condition
Data break caused by reading memory
Data break caused by writing to memory
Break caused by sequential break condition
Break at address xxxx caused by [Key break] button
Break caused by accessing no map area
Break caused by writing to ROM area
Break caused by accessing outside stack area
Break caused by signal input to S5U1C33104H/S5U1C33000H BRKIN pin
Break caused by executing illegal instruction in simulator mode
Break caused by S5U1C33xxxM bus break condition
Break caused by S5U1C33xxxM ce break condition
Break caused by S5U1C33xxxM area break condition
Break caused by S5U1C33xxxM map break
Table 16.13.1.1 Status messages
Table 16.13.2.1 Error messages
The specified address (symbol) is out of the mapped area.
The program code address is not a 2-byte boundary address.
The address mask is out of the range.
The address is out of the range.
The beginning address is larger than end address.
The address has been set to a break point.
The argument 1 is out of the range.
The argument 2 is out of the range.
The argument 3 is out of the range.
The software PC breakpoint number is out of the range.
The hardware PC breakpoint number is out of the range.
99 symbols have been registered.
Memory cannot be allocated.
The file cannot be closed.
The file information is incorrect.
An error has occurred during input process.
Memory allocation has failed.
The srf33 file load has failed; the file cannot be opened.
The srf33 file load has failed; the file cannot be read.
The srf33 file load has failed; memory cannot be allocated.
The srf33 file load has failed; some file other than srf33 executable
format is specified.
The debug information load has failed; the debug information is
illegal. (Program/ data is loaded successfully.)
The debug information load has failed; the source file cannot be
opened. (Program/ data is loaded successfully.)
The debug information load has failed; the source file cannot be
read. (Program/ data is loaded successfully.)
The debug information load has failed; memory cannot be allocated.
(Program/ data is loaded successfully.)
EPSON
(C COMPILER PACKAGE FOR S1C33 FAMILY) (Ver. 4)
Content
Content
S5U1C33000C MANUAL
(alphabetical order)