OM11077 NXP Semiconductors, OM11077 Datasheet - Page 147

• Manufacturer Part Number: OM11077
• Description: MODULE DIMM LPC2478 ARM7
• Manufacturer: NXP Semiconductors

Specifications of OM11077

• Accessory Type: Module Card
• For Use With/related Products: ARM-57TS-LPC2478
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-4742

NXP Semiconductors
Table 122. LPC2420/60/68 pin description
UM10237_4
User manual
Symbol
P2[6]/PCAP1[0]/
RI1/TRACEPKT1
P2[7]/RD2/
RTS1/
TRACEPKT2
P2[8]/TD2/
TXD2/
TRACEPKT3
P2[9]/
USB_CONNECT1/
RXD2/
EXTIN0
P2[10]/EINT0
P2[11]/EINT1/
MCIDAT1/
I2STX_CLK
P2[12]/EINT2/
MCIDAT2/
I2STX_WS
P2[13]/EINT3/
MCIDAT3/
I2STX_SDA
P2[14]/CS2/
CAP2[0]/SDA1
Pin
138
136
134
132
110
108
106
102
91
[6]
[6]
[1]
[1]
[1]
[1]
[6]
[6]
[6]
Ball
E17
G16
H15
H16
N15
T17
N14
T16
R12
[6]
[6]
[1]
[1]
[1]
[6]
[6]
[6]
[1]
Type
I/O
I
I
O
I/O
I
O
O
I/O
O
O
O
I/O
O
I
I
I/O
I
I/O
I
I/O
I/O
I/O
I
I/O
I/O
I/O
I
I/O
I/O
I/O
O
I
I/O
…continued
Rev. 04 — 26 August 2009
Description
P2[6] — General purpose digital input/output pin.
PCAP1[0] — Capture input for PWM1, channel 0.
RI1 — Ring Indicator input for UART1.
TRACEPKT1 — Trace Packet, bit 1.
P2[7] — General purpose digital input/output pin.
RD2 — CAN2 receiver input (LPC2460 only).
RTS1 — Request to Send output for UART1.
TRACEPKT2 — Trace Packet, bit 2.
P2[8] — General purpose digital input/output pin.
TD2 — CAN2 transmitter output (LPC2460 only).
TXD2 — Transmitter output for UART2.
TRACEPKT3 — Trace Packet, bit 3.
P2[9] — General purpose digital input/output pin.
USB_CONNECT1 — USB1 SoftConnect control. Signal used to switch
an external 1.5 kΩ resistor under the software control. Used with the
SoftConnect USB feature.
RXD2 — Receiver input for UART2.
EXTIN0 — External Trigger Input.
P2[10] — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip bootloader to
take over control of the part after a reset.
EINT0 — External interrupt 0 input.
P2[11] — General purpose digital input/output pin.
EINT1 — External interrupt 1 input.
MCIDAT1 — Data line 1 for SD/MMC interface.
I2STX_CLK — Transmit Clock. It is driven by the master and received by
the slave. Corresponds to the signal SCK in the I
P2[12] — General purpose digital input/output pin.
EINT2 — External interrupt 2 input.
MCIDAT2 — Data line 2 for SD/MMC interface.
I2STX_WS — Transmit Word Select. It is driven by the master and
received by the slave. Corresponds to the signal WS in the I
specification.
P2[13] — General purpose digital input/output pin.
EINT3 — External interrupt 3 input.
MCIDAT3 — Data line 3 for SD/MMC interface.
I2STX_SDA — Transmit data. It is driven by the transmitter and read by
the receiver. Corresponds to the signal SD in the I
P2[14] — General purpose digital input/output pin.
CS2 — LOW active Chip Select 2 signal.
CAP2[0] — Capture input for Timer 2, channel 0.
SDA1 — I
2
C1 data input/output (this is not an open-drain pin).
Chapter 8: LPC24XX Pin configuration
2
S-bus specification.
2
S-bus specification.
UM10237
© NXP B.V. 2009. All rights reserved.
2
S-bus
147 of 792