SPAKDSP303AG100 Freescale Semiconductor, SPAKDSP303AG100 Datasheet - Page 120

• Manufacturer Part Number: SPAKDSP303AG100
• Description: IC DSP 24BIT 100MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of SPAKDSP303AG100

• Interface: Host Interface, SSI, SCI
• Clock Rate: 100MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 24kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP
• Device Core Size: 24b
• Clock Freq (max): 100MHz
• Mips: 100
• Device Input Clock Speed: 100MHz
• Ram Size: 24KB
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Host Interface (HI08)
registers (TXH:TXM:TXL on the host side) when both the transmit data register empty
(ISR[TXDE]) on the host side and host receive data full (HSR[HRDF]) on the DSP side are
cleared. The transfer operation sets both ISR[TXDE] and HSR[HRDF]. When the HSR[HRDF]
is set, the HRX register contains valid data. The DSP56303 can set the HCR[HRIE] to cause a
host receive data interrupt when HSR[HRDF] is set. When the DSP56303 reads the HRX
register, the HSR[HRDF] bit is cleared.
Note:
6.6.9 DSP-Side Registers After Reset
Table 6-13 shows the results of the four reset types on the bits in each of the HI08 registers
accessible to the DSP56303. The hardware reset (HW) is caused by the
software reset (SW) is caused by execution of the RESET instruction. The individual reset (IR)
occurs when HPCR[HEN] is cleared. The stop reset (ST) occurs when the STOP instruction
executes.
6.7 Host Programmer Model
The HI08 provides a simple, high-speed interface to a host processor. To the host bus, the HI08
appears to be eight byte-wide registers. Separate transmit and receive data paths are
double-buffered to allow the DSP core and host processor to transfer data efficiently at high
speed. The host can access the HI08 asynchronously using polling techniques or interrupt-based
6-20
Note:
Register
HDDR
Name
HPCR
HBAR
HCR
HSR
HDR
HRX
HTX
A long dash (—) denotes that the bit value is not affected by the specified reset.
The DSP56303 should never try to read the HRX register if the HSR[HRDF] bit is
already cleared.
HRX [23–0]
HTX [23–0]
DR[15–0]
BA[10–3]
Register
HF[1–0]
D[15–0]
All bits
All bits
HRDF
HTDE
Data
HCP
Table 6-13. DSP-Side Registers After Reset
DSP56303 User’s Manual, Rev. 2
Reset
empty
empty
HW
$80
—
0
0
0
0
1
0
0
Reset
empty
empty
$80
SW
—
0
0
0
0
1
0
0
Reset Type
Reset
empty
empty
RESET
IR
—
—
—
—
—
—
0
1
0
Freescale Semiconductor
signal. The
Reset
empty
empty
ST
—
—
—
—
—
—
0
1
0