HD6417751RF240V Renesas Electronics America, HD6417751RF240V Datasheet - Page 700

• Manufacturer Part Number: HD6417751RF240V
• Description: MPU 1.5/3.3V 0K PB-FREE 256-QFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7750r

Specifications of HD6417751RF240V

• Core Processor: SH-4
• Core Size: 32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, FIFO, SCI, SmartCard
• Peripherals: DMA, POR, WDT
• Number Of I /o: 39
• Program Memory Type: ROMless
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.4 V ~ 1.6 V
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 256-QFP Exposed Pad, 256-eQFP, 256-HQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

14. Direct Memory Access Controller (DMAC)
14.9
1. When modifying SAR0–SAR3, DAR0–DAR3, DMATCR0–DMATCR3, and CHCR0–
2. The NMIF bit in DMAOR is set when an NMI interrupt is input even if the DMAC is not
3. Check that DMA transfer is not in progress before making a transition to the module standby
4. Do not specify a DMAC, CCN, BSC, UBC, or PCIC control register as the DMAC transfer
5. When activating the DMAC, make the SAR, DAR, and DMATCR register settings for the
6. After the DMATCR count reaches 0 and DMA transfer ends normally, always write 0 to
Rev.4.00 Oct. 10, 2008 Page 600 of 1122
REJ09B0370-0400
CHCR3 in the SH7751 or when modifying SAR0–SAR7, DAR0–DAR7, DMATCR0–
DMATCR7, and CHCR0–CHCR7 in the SH7751R, first clear the DE bit for the relevant
channel to 0.
operating.
Confirmation method when DMA transfer is not executed correctly:
With the SH7751, read the NMIF, AE, and DME bits in DMAOR, the DE and TE bits in
CHCR0–CHCR3, and DMATCR0–DMATCR3.
With the SH7751R, read the NMIF, AE, and DME bits in DMAOR, the DE and TE bits in
CHCR0–CHCR7, and DMATCR0–DMATCR7. If NMIF was set before the transfer, the
DMATCR transfer count will remain at the set value. If NMIF was set during the transfer,
when the DE bit is 1 and the TE bit is 0 in CHCR0–CHCR3 in the SH7751 or CHCR0–
CHCR7 in the SH7751R, the DMATCR value will indicate the remaining number of transfers.
Also, the next addresses to be accessed can be found by reading SAR0–SAR3 and DAR0–
DAR3 in the SH7751 or SAR0–SAR7 and DAR0–DAR7 in the SH7751R. If the AE bit has
been set, an address error has occurred. Check the set values in CHCR, SAR, and DAR.
state, standby mode, or deep sleep mode.
Either check that TE = 1 in the SH7751's CHCR0–CHCR3 or in the SH7751R's CHCR0–
CHCR7, or clear DME to 0 in DMAOR to terminate DMA transfer. When DME is cleared to 0
in DMAOR, transfer halts at the end of the currently executing DMA bus cycle. Note,
therefore, that transfer may not end immediately, depending on the transfer data size. DMA
operation is not guaranteed if the module standby state, standby mode, or deep sleep mode is
entered without confirming that DMA transfer has ended.
source or destination.
relevant channel before setting DE to 1 in CHCR, or make the register settings with DE
cleared to 0 in CHCR, then set DE to 1. It does not matter whether setting of the DME bit to 1
in DMAOR is carried out first or last. To operate the relevant channel, DME and DE must both
be set to 1. The DMAC may not operate normally if the SAR, DAR, and DMATCR settings
are not made (with the exception of the unused register in single address mode).
DMATCR even when executing the maximum number of transfers on the same channel.
Usage Notes