MC9S12P32CFT Freescale Semiconductor, MC9S12P32CFT Datasheet - Page 439

• Manufacturer Part Number: MC9S12P32CFT
• Description: MCU 16BIT 32K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12P32CFT

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: S12P
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, DEMO9S12PFAME
• Package: 48QFN EP
• Family Name: HCS12
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: CAN/SCI/SPI
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.3.2.7
The FSTAT register reports the operational status of the Flash module.
1. Reset value can deviate from the value shown if a double bit fault is detected during the reset sequence (see
CCIF, ACCERR, and FPVIOL bits are readable and writable, MGBUSY and MGSTAT bits are readable
but not writable, while remaining bits read 0 and are not writable.
Freescale Semiconductor
ACCERR
Offset Module Base + 0x0006
DFDIE
Reset
SFDIE
FPVIOL
Field
Field
CCIF
1
0
W
7
5
4
R
CCIF
Double Bit Fault Detect Interrupt Enable — The DFDIE bit controls interrupt generation when a double bit fault
is detected during a Flash block read operation.
0 DFDIF interrupt disabled
1 An interrupt will be requested whenever the DFDIF flag is set (see
Single Bit Fault Detect Interrupt Enable — The SFDIE bit controls interrupt generation when a single bit fault
is detected during a Flash block read operation.
0 SFDIF interrupt disabled whenever the SFDIF flag is set (see
1 An interrupt will be requested whenever the SFDIF flag is set (see
Flash Status Register (FSTAT)
1
7
Command Complete Interrupt Flag — The CCIF flag indicates that a Flash command has completed. The
CCIF flag is cleared by writing a 1 to CCIF to launch a command and CCIF will stay low until command
completion or command violation.
0 Flash command in progress
1 Flash command has completed
Flash Access Error Flag — The ACCERR bit indicates an illegal access has occurred to the Flash memory
caused by either a violation of the command write sequence (see
command. While ACCERR is set, the CCIF flag cannot be cleared to launch a command. The ACCERR bit is
cleared by writing a 1 to ACCERR. Writing a 0 to the ACCERR bit has no effect on ACCERR.
0 No access error detected
1 Access error detected
Flash Protection Violation Flag —The FPVIOL bit indicates an attempt was made to program or erase an
address in a protected area of P-Flash or D-Flash memory during a command write sequence. The FPVIOL
bit is cleared by writing a 1 to FPVIOL. Writing a 0 to the FPVIOL bit has no effect on FPVIOL. While FPVIOL
is set, it is not possible to launch a command or start a command write sequence.
0 No protection violation detected
1 Protection violation detected
= Unimplemented or Reserved
0
0
6
Figure 13-11. Flash Status Register (FSTAT)
Table 13-13. FERCNFG Field Descriptions
S12P-Family Reference Manual, Rev. 1.13
ACCERR
Table 13-14. FSTAT Field Descriptions
0
5
FPVIOL
0
4
Description
Description
MGBUSY
0
3
Section
Section
128 KByte Flash Module (S12FTMRC128K1V1)
Section
Section
RSVD
13.3.2.8)
0
2
13.4.3.2) or issuing an illegal Flash
13.3.2.8)
13.3.2.8)
0
1
(1)
MGSTAT[1:0]
Section
0
0
1
13.6).
439