TMPA901CMXBG Toshiba, TMPA901CMXBG Datasheet - Page 471

• Manufacturer Part Number: TMPA901CMXBG
• Description: Microcontrollers (MCU) 32-bit RISC MCU 16kb ARM926EJ 16kb 200Mhz
• Manufacturer: Toshiba

Specifications of TMPA901CMXBG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): -
• Rom Type: ROMless
• Ram (kbytes): 32
• Number Of Pins: 177
• Package: BGA
• Vcc: 3V
• Tft Lcd Controller: Y
• Touchscreen Controller: Y
• Usb Host Fs With Phy: Y
• Usb Device Hs With Phy: Y
• Sd Host Controller: -
• Cmos Image Sensor Interface: -
• I2s: 1
• Ssp (ch) Spi: 1
• I2mc/sio (ch): 1
• Uart/sio (ch): 2
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 8
• 10-bit Ad Converter: 4
• 12-bit Da Converter: -
• 16-bit Timer / Counter: 6
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Low-power Modes: Y
• Lead Free Status / Rohs Status: Details

[31:8]
[7]
[6]
[5]
[4]
[3]
[2]
[1]
[0]
Bit
[Description]
wakeup_en
phy_remote_wkup
phy_resetb
suspend_x
phy_suspend
pw_detect
pw_resetb
usb_reset
a. <wakeup_en>
Symbol
19. UDPWCTL (Power Detect Control register)
Set this bit to '1' if you want the system (AHB end) to sleep to stop CLK_H when the USB
is suspended. If this bit is set to 1, the WAKEUP_X signal will be asserted to 0
asynchronously when the suspended status is cancelled (suspend_x = 1) or the system is
disconnected (VBUSPOWER = 0), making it available for resuming the system.
See also section 3.16.2.13 “(4) Signal operations when suspended and resumed
(disconnected)” for more information on using this bit.
0y0: Do not assert the WAKEUP_X signal
0y1: Assert the WAKEUP_X signal
Note 1: While UDC2AB originally has the function to assert the Wakeup signal, it is not supported for this LSI.
Note 2: While UDC2AB originally has the function to assert the int_powerdetect interrupt when VBUS is
Note: While UDC2AB originally has the function to assert the Wakeup signal, it is not supported for this LSI.
Bit
Controls UDC2AB when reset/suspended.
detected, it is not supported for this LSI. Power Detect Control<pw_detect> always indicates 0.
Undefined
R/W
R/W1S
R/W
RO
R/W
RO
R/W
RO
Type
0y0, (-)
0y0, (-)
0y1, (-)
0y1
0y0, (-)
0y0, (-)
0y1, (-)
0y0
TMPA901CM- 470
Reset
Value
Read as undefined. Write as zero.
0y0: Do not assert the WAKEUP_X signal
0y1: Assert the WAKEUP_X signal
(Note 1)
0y0: No operation
0y1: Wakeup
PHY reset
0y0: Reset asserted
0y1: Reset deasserted
0y0: Suspended (suspend_x = 0)
0y1: Not suspended (suspend_x = 1)
0y0: Not suspended
0y1: Suspended
0y0: USB bus disconnected (VBUSPOWER = 0)
0y1: USB bus connected (VBUSPOWER = 1)
(Note 2)
Power reset
0y0: Reset asserted
0y1: Reset deasserted
USB_RESET
0y0: usb_reset = 0
0y1: usb_reset = 1
Wakeup enable
Remote wakeup
Suspend detection
PHY suspend
USB bus power detect
Description
Address = (0xF440_0000) + (0x0080)
TMPA901CM
2010-07-29