EP2AGX190FF35C6N Altera, EP2AGX190FF35C6N Datasheet - Page 579

• Manufacturer Part Number: EP2AGX190FF35C6N
• Description: IC ARRIA II GX 190K 1152FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX190FF35C6N

• Number Of Logic Elements/cells: 181165
• Number Of Labs/clbs: 7612
• Total Ram Bits: 9939
• Number Of I /o: 612
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1152-FBGA
• Family Name: Arria® II GX
• Number Of Logic Blocks/elements: 190300
• # I/os (max): 612
• Frequency (max): 400MHz
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 190300
• Ram Bits: 10380902.4
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1152
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Chapter 4: Reset Control and Power Down in Arria II Devices
Transceiver Reset Sequences
Figure 4–2. Transceiver Reset Sequences Chart
Note to
(1) Refer to the Timing Diagram in
(2) Refer to the Timing Diagram in
(3) Refer to the Timing Diagram in
(4) Refer to the Timing Diagram in
(5) Refer to the Timing Diagram in
(6) Refer to the Timing Diagram in
(7) Refer to the Timing Diagram in
(8) Refer to the Timing Diagram in
December 2010 Altera Corporation
"Transmitter Only"
Figure
Channel (2)
4–2:
1
1
Bonded
Receiver CDR
Lock Mode (3)
in Automatic
The busy signal remains low for the first reconfig_clk clock cycle. It is then asserted
from the second reconfig_clk clock cycle. Subsequent de-assertion of the busy signal
indicates the completion of the offset cancellation process. This busy signal is
required in transceiver reset sequences except for Transmitter Only channel
configurations. Refer to the reset sequences shown in
references listed in the notes.
Altera strongly recommends adhering to these reset sequences for proper operation of
the Arria II transceiver.
Transmitter" Channel
"Receiver and
Figure 4–10 on page
Figure 4–3 on page
Figure 4–4 on page
Figure 4–5 on page
Figure 4–6 on page
Figure 4–7 on page
Figure 4–8 on page
Figure 4–9 on page
Receiver CDR
Lock Mode (4)
in Manual
functional modes
All supported
except PCIe
4–7.
4–8.
4–9.
4–11.
4–12.
4–13.
4–14.
4–15.
"Transmitter Only"
Channel (2)
Non-Bonded
Reset Sequence
Receiver CDR
Lock Mode (5)
in Automatic
"Receiver Only"
Channel
Receiver CDR
Lock Mode (6)
in Manual
PCI Express (PIPE)
Arria II Device Handbook Volume 2: Transceivers
Normal Operation
Compliance and
Initialization and
Phases (1)
Figure 4–2
Receiver CDR
Lock Mode (7)
in Automatic
and the associated
Transmitter" Channel
"Receiver and
Receiver CDR
Lock Mode (8)
in Manual
4–5