EP2AGX190FF35C6N Altera, EP2AGX190FF35C6N Datasheet - Page 514

• Manufacturer Part Number: EP2AGX190FF35C6N
• Description: IC ARRIA II GX 190K 1152FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX190FF35C6N

• Number Of Logic Elements/cells: 181165
• Number Of Labs/clbs: 7612
• Total Ram Bits: 9939
• Number Of I /o: 612
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1152-FBGA
• Family Name: Arria® II GX
• Number Of Logic Blocks/elements: 190300
• # I/os (max): 612
• Frequency (max): 400MHz
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 190300
• Ram Bits: 10380902.4
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1152
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

2–24
Table 2–6. Receiver Datapath Clock Frequencies in ×4 Bonded Functional Modes with Deskew FIFO for Arria II Devices
Arria II Device Handbook Volume 2: Transceivers
Notes to
(1) 250 MHz when you enable the PCIe hard IP.
(2) Arria II GZ devices only.
PCIe ×4 (Gen 2)
Functional Mode
PCIe ×4 (Gen 1)
XAUI
Table
2–6:
(2)
In ×4 bonded channel configurations with deskew FIFO, the CDR in each receiver
channel recovers the serial clock from the received data. Also, the serial recovered
clock frequency is half the configured data rate due to the half-rate CDR architecture.
The serial recovered clock is divided within each channel’s receiver PMA to generate
the parallel recovered clock. The deserializer uses the serial recovered clock in the
receiver PMA. The parallel recovered clock and deserialized data is forwarded to the
receiver PCS in each channel.
The parallel recovered clock from the receiver PMA in each channel clocks the word
aligner in that channel. The parallel recovered clock from the Channel 0 clocks the
deskew FIFO and the write port of the rate match FIFO in all four bonded channels.
The low-speed parallel clock from the CMU0 clock divider block clocks the read port of
the rate match FIFO, the 8B/10B decoder, and the write port of the byte deserializer (if
enabled) in all four bonded channels. The low-speed parallel clock or its
divide-by-two version (if byte deserializer is enabled) clocks the write port of the
receiver phase compensation FIFO. It is also driven on the coreclkout port as the
FPGA fabric-transceiver interface clock. You can use the coreclkout signal to latch the
receiver data and status signals in the FPGA fabric for all four bonded channels.
In ×4 bonded channel configurations, the receiver phase compensation FIFOs in all
four bonded channels share common read and write pointers and enable signals
generated in the CMU0 block of the transceiver block.
Table 2–6
with deskew FIFO.
Data Rate
(Gbps)
3.125
2.5
5
lists the receiver datapath clock frequencies in ×4 bonded functional modes
Recovered
Frequency
1.5625
Serial
Clock
(GHz)
1.25
2.5
Transmitter PCS Clock
Parallel Recovered
Clock and Parallel
Frequency (MHz)
312.5
250
500
Chapter 2: Transceiver Clocking in Arria II Devices
FPGA Fabric-Transceiver Interface
Without Byte
Serializer
—
Transceiver Channel Datapath Clocking
—
—
December 2010 Altera Corporation
(1)
Clock Frequency
Serializer (MHz)
With Byte
156.25
125
250