EP2AGX190FF35C6N Altera, EP2AGX190FF35C6N Datasheet - Page 406

• Manufacturer Part Number: EP2AGX190FF35C6N
• Description: IC ARRIA II GX 190K 1152FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX190FF35C6N

• Number Of Logic Elements/cells: 181165
• Number Of Labs/clbs: 7612
• Total Ram Bits: 9939
• Number Of I /o: 612
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1152-FBGA
• Family Name: Arria® II GX
• Number Of Logic Blocks/elements: 190300
• # I/os (max): 612
• Frequency (max): 400MHz
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 190300
• Ram Bits: 10380902.4
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1152
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

1–20
Arria II Device Handbook Volume 2: Transceivers
1
Transmitter Output Buffer
The Arria II GX and GZ transmitter output buffers support the 1.5-V pseudo current
mode logic (PCML) I/O standard and can drive 40 inches of FR4 trace (with 50-
impedance) across two connectors.
For data rates > 3.75 Gbps, Altera recommends limiting the FR4 trace length to
15 inches.
The transmitter output buffer power supply (V
transmitter output buffers in the transceiver channels. This is set to 1.5 V in the
ALTGX MegaWizard Plug-In Manager. The common mode voltage (V
Arria II GX and GZ transmitter output buffers is 650 mV.
To improve signal integrity, the transmitter output buffer has the following additional
circuitry, which you can set in the ALTGX MegaWizard Plug-In Manager:
■
■
■
Programmable differential output voltage (V
customize the V
various receiver requirements.
Programmable pre-emphasis—Pre-emphasis boosts high frequencies in the
transmit data signal, which might be attenuated in the transmission media
because of data-dependent jitter and other intersymbol interference (ISI) effects. It
equalizes the frequency response at the receiver so the differences between the
low-frequency and high-frequency components are reduced, minimizing the ISI
effects from the transmission medium.
Programmable differential on-chip termination (OCT)—The Arria II GX and GZ
transmitter buffer includes a differential OCT of 85  (for Arria II GZ only) or
100  . The resistance is adjusted in the calibration block to compensate for
temperature, voltage, and process changes (for more information, refer to
“Calibration Block” on page
1
Pre-emphasis requirements increase as data rates through legacy backplanes
increase. Using pre-emphasis can maximize the data eye opening at the far-end
receiver.
You can set the transmitter termination setting in the ALTGX MegaWizard Plug-In
Manager or through the Quartus II Assignment Editor by setting the assignment
output termination to 85 (Arria II GZ only) or 100 on the transmitter output
buffer.
You can disable OCT and use external termination. In this case, the transmitter
common mode is tri-stated.
The Arria II GX and GZ transmitter output buffers in the transceiver block
are current-mode drivers. The resulting V
termination value.
OD
to handle different trace lengths, various backplanes, and
1–47).
Chapter 1: Transceiver Architecture in Arria II Devices
CCH
OD
)—This feature allows you to
) only provides voltage to the
OD
is a function of the transmitter
December 2010 Altera Corporation
Transmitter Channel Datapath
CM
) for the