HD6432621 Hitachi, HD6432621 Datasheet - Page 712
HD6432621
Manufacturer Part Number
HD6432621
Description
(HD64F262x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432621.pdf
(1069 pages)
- Current page: 712 of 1069
- Download datasheet (5Mb)
19.13
Precautions concerning the use of on-board programming mode, the RAM emulation function, and
programmer mode are summarized below.
1. Use the specified voltages and timing for programming and erasing.
2. Powering on and off (see figures 19-26 to 19-28)
3. FWE application/disconnection (see figures 19-26 to 19-28)
668
Applied voltages in excess of the rating can permanently damage the device. Use a PROM
programmer that supports the Hitachi microcomputer device type with 256-kbyte on-chip flash
memory (FZTAT256V3A).
Do not select the HN27C4096 setting for the PROM programmer, and only use the specified
socket adapter. Failure to observe these points may result in damage to the device.
Do not apply a high level to the FWE pin until V
before turning off V
When applying or disconnecting V
in the hardware protection state.
The power-on and power-off timing requirements should also be satisfied in the event of a
power failure and subsequent recovery.
FWE application should be carried out when MCU operation is in a stable condition. If MCU
operation is not stable, fix the FWE pin low and set the protection state.
The following points must be observed concerning FWE application and disconnection to
prevent unintentional programming or erasing of flash memory:
•
•
•
•
•
Apply FWE when the V
Apply FWE when oscillation has stabilized (after the elapse of the oscillation settling
time).
In boot mode, apply and disconnect FWE during a reset.
In user program mode, FWE can be switched between high and low level regardless of
RES input.
FWE input can also be switched during execution of a program in flash memory.
Do not apply FWE if program runaway has occurred.
Disconnect FWE only when the SWE1, ESU1, PSU1, EV1, PV1, P1, and E1 bits in
FLMCR1 are cleared.
Make sure that the SWE1, ESU1, PSU1, EV1, PV1, P1, and E1 bits are not set by mistake
when applying or disconnecting FWE.
Flash Memory Programming and Erasing Precautions
CC
.
CC
voltage has stabilized within its rated voltage range.
CC
power, fix the FWE pin low and place the flash memory
CC
has stabilized. Also, drive the FWE pin low
Related parts for HD6432621
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: