HD6432621 Hitachi, HD6432621 Datasheet - Page 689
HD6432621
Manufacturer Part Number
HD6432621
Description
(HD64F262x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432621.pdf
(1069 pages)
- Current page: 689 of 1069
- Download datasheet (5Mb)
19.7.3
When erasing flash memory, the single-block erase/erase-verify flowchart shown in figure 19-12
should be followed.
To erase flash memory contents, make a 1-bit setting for the flash memory area to be erased in
erase block register 1 and 2 (EBR1, EBR2) at least (x) µs after setting the SWE1 bit to 1 in
FLMCR1. Next, the watchdog timer (WDT) is set to prevent overerasing due to program
runaway, etc. Set 6.6 ms as the WDT overflow period. Preparation for entering erase mode (erase
setup) is performed next by setting the ESU1 bit in FLMCR1. The operating mode is then
switched to erase mode by setting the E1 bit in FLMCR1 after the elapse of at least (y) µs. The
time during which the E1 bit is set is the flash memory erase time. Ensure that the erase time does
not exceed (z) ms.
Note: With flash memory erasing, preprogramming (setting all memory data in the memory to
19.7.4
In erase-verify mode, data is read after memory has been erased to check whether it has been
correctly erased.
After the elapse of the fixed erase time, clear the E1 bit in FLMCR1, then wait for at least ( ) µs
before clearing the ESU1 bit to exit erase mode. After exiting erase mode, the watchdog timer is
cleared after the elapse of ( ) µs or more. The operating mode is then switched to erase-verify
mode by setting the EV1 bit in FLMCR1. Before reading in erase-verify mode, a dummy write of
H'FF data should be made to the addresses to be read. The dummy write should be executed after
the elapse of ( ) µs or more. When the flash memory is read in this state (verify data is read in 16-
bit units), the data at the latched address is read. Wait at least ( ) µs after the dummy write before
performing this read operation. If the read data has been erased (all 1), a dummy write is
performed to the next address, and erase-verify is performed. If the read data is unerased, set erase
mode again and repeat the erase/erase-verify sequence in the same way. The maximum number of
reoperations of the erase/erase-verify sequence is indicated by the maximum erase count (N).
However, ensure that the erase/erase-verify sequence is not repeated more than (N) times. When
verification is completed, exit erase-verify mode, and wait for at least ( ) µs. If erasure has been
completed on all the erase blocks, clear the SWE1 bit in FLMCR1. If there are any unerased
blocks, make a 1 bit setting for the flash memory area to be erased, and repeat the erase/erase-
verify sequence as before.
be erased to all 0) is not necessary before starting the erase procedure.
Erase Mode
Erase-Verify Mode
645
Related parts for HD6432621
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: