TMPM370FYFG Toshiba, TMPM370FYFG Datasheet - Page 120

• Manufacturer Part Number: TMPM370FYFG
• Manufacturer: Toshiba

Specifications of TMPM370FYFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 256K
• Rom Type: Flash
• Ram (kbytes): 10K
• Number Of Pins: 100
• Package: LQFP(14x14)
• Vcc: 5V
• Cpu Mhz: 80
• Ssp (ch) Spi: -
• I2c/sio (ch): -
• Uart/sio (ch): 4
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 27
• 16-bit Timer / Counter: 8
• Motor / Igbt Control: Vector Engine
• Real Time Clock: -
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: 4
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

PKFR1
(0x4000_0288)
PKDATA
(0x4000_0280)
PKCR
(0x4000_0284)
8.2.12 Port K (PK0 to PK1)
specified in units of bits. Besides the general-purpose input/output function, the port K performs the
functions as the analog input of the A/D converter and the external interrupt input.
disabled.
and enable input in the PKIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note 1) In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
(Note 2) Unless you use all the bits of port K as analog input pins, conversion accuracy may be
The port K is a general-purpose, 2-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port K as general-purpose ports with input, output, pull-up and pull-down
To use the external interrupt input for releasing STOP mode, select this function in the PKFR1 register
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Bit Symbol
Read/Write
After reset
Function
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
reduced. Be sure to verify that this causes no problem on your system.
Type
－
－
－
－
7
7
7
7
－
－
－
－
6
6
6
6
Port K function register 1
Port K control register
Port K circuit type
TMPM370 8-23
Port K register
－
－
－
－
5
5
5
5
“0” is read.
“0” is read
“0” is read
R
R
R
0
0
－
－
－
－
4
4
4
4
－
－
－
－
3
3
3
3
－
－
－
－
2
2
2
2
Input/Output Ports
0:PORT
PK1F1
1: INTF
PK1C
PK1
T17
1
1
1
1
0
0
1: enabled
0: disabled
Output
R/W
R/W
R/W
“0”
TMPM370
0:PORT
PK0F1
1: INTE
PK0C
T17
PK0
0
0
0
0
0
0