TMPM370FYFG Toshiba, TMPM370FYFG Datasheet - Page 118

• Manufacturer Part Number: TMPM370FYFG
• Manufacturer: Toshiba

Specifications of TMPM370FYFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 256K
• Rom Type: Flash
• Ram (kbytes): 10K
• Number Of Pins: 100
• Package: LQFP(14x14)
• Vcc: 5V
• Cpu Mhz: 80
• Ssp (ch) Spi: -
• I2c/sio (ch): -
• Uart/sio (ch): 4
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 27
• 16-bit Timer / Counter: 8
• Motor / Igbt Control: Vector Engine
• Real Time Clock: -
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: 4
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

PJFR1
(0x4000_0248)
PJDATA
(0x4000_0240)
PJCR
(0x4000_0244)
8.2.11 Port J (PJ0 to PJ7)
specified in units of bits. Besides the general-purpose input/output function, the port J performs the
analog input of the A/D converter and external interrupt input.
disabled.
and enable input in the PJIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note 1) In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
(Note 2) Unless you use all the bits of port J as analog input pins, conversion accuracy may be
The port J is a general-purpose, 8-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port J as general-purpose ports with input, output, pull-up and pull-down
To use the external interrupt input for releasing STOP mode, select this function in the PJFR1 register
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Bit Symbol
Read/Write
After reset
Function
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
reduced. Be sure to verify that this causes no problem on your system.
Type
0:PORT
1:INTD
PJ7F1
PJ7C
T17
PJ7
7
7
7
7
0
0
R/W
0:PORT
1:INTC
PJ6F1
PJ6C
T17
PJ6
6
0
6
6
6
0
Port J function register 1
Port J control register
TMPM370 8-21
Port J circuit type
Port J register
PJ5C
T16
PJ5
－
5
5
5
5
0
0
PJ4C
T16
PJ4
－
4
4
4
4
0
0
0: disabled
1: enabled
Output
R/W
R/W
“0”
PJ3C
T16
PJ3
－
3
3
3
3
0
0
“0” is read
R
PJ2C
T16
PJ2
－
2
2
2
2
0
0
Input/Output Ports
PJ1C
T16
PJ1
－
1
1
1
1
0
0
TMPM370
PJ0C
T16
PJ0
0
－
0
0
0
0
0