R5S72611 RENESAS [Renesas Technology Corp], R5S72611 Datasheet - Page 1175
R5S72611
Manufacturer Part Number
R5S72611
Description
32-Bit RISC Microcomputer SuperHTM RISC engine Family / SH7260 Series
Manufacturer
RENESAS [Renesas Technology Corp]
Datasheet
1.R5S72611.pdf
(1348 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
R5S72611P100FP
Manufacturer:
ACTEL
Quantity:
90
Part Number:
R5S72611P100FP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
R5S72611P100FPV
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
R5S72611RB120FPV
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
- Current page: 1175 of 1348
- Download datasheet (9Mb)
27.3.2
(1)
The LSI switches from a program execution state to software standby mode by executing the
SLEEP instruction when the STBY bit and DEEP bit in STBCR are 1 and 0 respectively. In
software standby mode, not only the CPU but also the clock and on-chip peripheral modules halt.
The clock output from the CKIO pin also halts in clock mode 0 or 2.
The contents of the CPU and cache registers remain unchanged. Some registers of on-chip
peripheral modules are, however, initialized. As for the states of on-chip peripheral module
registers in software standby mode, see section 30.3, Register States in Each Operating Mode.
The CPU takes one cycle to finish writing to STBCR, and then executes processing for the next
instruction. However, it takes one or more cycles to actually write. Therefore, execute a SLEEP
instruction after reading STBCR to have the values written to STBCR by the CPU to be definitely
reflected in the SLEEP instruction.
The procedure for switching to software standby mode is as follows:
1. Clear the TME bit in the WDT's timer control register (WTCSR) to 0 to stop the WDT.
2. Set the WDT's timer counter (WTCNT) to 0 and the CKS[2:0] bits in WTCSR to appropriate
3. After setting the STBY and DEEP bits in STBCR to 1 and 0 respectively, read STBCR. Then,
(2)
Software standby mode is canceled by interrupts (NMI or IRQ) or a reset (manual reset or power-
on reset). In clock modes 0 and 2, a clock signal starts to be output from the CKIO pin.
• Canceling with an interrupt
values to secure the specified oscillation settling time.
execute a SLEEP instruction.
When the falling edge or rising edge of the NMI pin (selected by the NMI edge select bit
(NMIE) in interrupt control register 0 (ICR0) of the interrupt controller (INTC)) or the falling
edge or rising edge of an IRQ pin (IRQ7 to IRQ0) (selected by the IRQn sense select bits
(IRQn1S and IRQn0S) in interrupt control register 1 (ICR1) of the interrupt controller (INTC))
is detected, clock oscillation is started. This clock pulse is supplied only to the oscillation
settling counter (WDT) used to count the oscillation settling time.
Transition to Software Standby Mode
Canceling Software Standby Mode
Software Standby Mode
Rev. 2.00 Sep. 07, 2007 Page 1143 of 1312
Section 27 Power-Down Modes
REJ09B0320-0200
Related parts for R5S72611
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer Renesas H8S Family/H8S/2100 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family / H8S/2200 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family H8S-2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family/H8S/2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family/H8S/2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8 Family/H8/300H Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit Single-Chip RISC Microprocessor SuperH RISC engine Family/SH7040 Series(CPU Core SH-2)
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer SuperHTM RISC engine Family / SH7700 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer SuperH RISC engine Family / SH7641 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet: