SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 872

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Table 44-38. SSC Timings (Continued)
Notes:
872
Symbol
SSC
SSC
SSC
SSC
SSC
9
10
11
12
13
1. Timings SSC4 and SSC7 depend on the start condition. When STTDLY = 0 (Receive start delay) and START = 4, or 5 or 7
2. For output signals (TF, TD, RF), Min and Max access times are defined. The Min access time is the time between the TK (or
AT91SAM9R64/RL64
(Receive Start Selection), two Periods of the MCK must be added to timings.
RK) edge and the signal change. The Max access timing is the time between the TK edge and the signal stabilization. Figure
18 illustrates Min and Max accesses for SSC0. The same applies for SSC1, SSC4, and SSC7, SSC10 and SSC13.
Parameter
RF/RD hold time after RK edge (RK input)
RK edge to RF (RK input)
RF/RD setup time before RK edge (RK output)
RF/RD hold time after RK edge (RK output)
RK edge to RF (RK output)
Cond
MAX corner, VDDIO = 1.8V
MAX corner, VDDIO = 3.3V
MAX corner, VDDIO = 1.8V
MAX corner, VDDIO = 3.3V
MAX corner, VDDIO = 1.8V
MAX corner, VDDIO = 3.3V
MAX corner, VDDIO = 1.8V
MAX corner, VDDIO = 3.3V
MAX corner, VDDIO = 1.8V
MAX corner, VDDIO = 3.3V
t
t
t
t
13.3
13.3
t
t
CPMCK
CPMCK
12.6 -
13.7 -
CPMCK
CPMCK
CPMCK
CPMCK
10.7
10.7
Min
0
0
(2)
(2)
(2)
(2)
-
-
15.2
16.3
1.8
2.9
Max
6289D–ATARM–3-Oct-11
(2)
(2)
(2)
(2)
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns