SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 775

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.5.11
Name:
Access Type:
• SPEED_CFG: Speed Configuration
Read/Write:
Speed Configuration:
• TST_J: Test J Mode
Read and write:
0 = no effect.
1 = set to send the J state on the UDPHS line. This enables the testing of the high output drive level on the D+ line.
• TST_K: Test K Mode
Read and write:
0 = no effect.
1 = set to send the K state on the UDPHS line. This enables the testing of the high output drive level on the D- line.
• TST_PKT: Test Packet Mode
Read and write:
0 = no effect.
1 = set to repetitively transmit the packet stored in the current bank. This enables the testing of rise and fall times, eye pat-
terns, jitter, and any other dynamic waveform specifications.
• OPMODE2: OpMode2
Read and write:
6289D–ATARM–3-Oct-11
00
01
10
11
31
23
15
–
–
–
7
–
UDPHS Test Register
Normal Mode: The macro is in Full Speed mode, ready to make a High Speed identification, if the host supports it and then
to automatically switch to High Speed mode
Reserved
Force High Speed: Set this value to force the hardware to work in High Speed mode. Only for debug or test purpose.
Force Full Speed: Set this value to force the hardware to work only in Full Speed mode. In this configuration, the macro will
not respond to a High Speed reset handshake
30
22
14
UDPHS_TST
Read/Write
–
–
–
6
–
OPMODE2
29
21
13
–
–
–
5
TST_PKT
28
20
12
–
–
–
4
TST_K
27
19
11
–
–
–
3
TST_J
AT91SAM9R64/RL64
26
18
10
–
–
–
2
25
17
–
–
9
–
1
SPEED_CFG
24
16
–
–
8
–
0
775