SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 674

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.9
Figure 39-11. Frame Buffer Addressing
674
2D Memory Addressing
AT91SAM9R64/RL64
The host updates the backbuffer while the LCD Controller is displaying the primary buffer. When
the backbuffer has been updated the host updates the DMA Base Address registers.
When using a Dual Panel LCD Module, both base address pointers should be updated in the
same frame. There are two possibilities:
Once the host has updated the Frame Base Address Registers and the next DMA end of frame
IRQ arrives, the backbuffer and the primary buffer are swapped and the host can work with the
new backbuffer.
When using a dual-panel LCD module, both base address pointers should be updated in the
same frame. In order to achieve this, the DMAUPDT bit in DMACON register must be used to
validate the new base address.
The LCDC can be configured to work on a frame buffer larger than the actual screen size. By
changing the values in a few registers, it is easy to move the displayed area along the frame buf-
fer width and height.
In order to locate the displayed window within a larger frame buffer, the software must:
• Check the DMAFRMPTx register to ensure that there is enough time to update the DMA
• Update the Frame Base Address Registers when the End Of Frame IRQ is generated.
• Program the DMABADDR1 (DMABADDR2) register(s) to make them point to the word
• Program the PIXELOFF field of DMA2DCFG register to specify the offset of this first pixel
• Define the width of the complete frame buffer by programming in the field ADDRINC of
• Enable the 2D addressing mode by writing the DMA2DEN bit in DMACON register. If this bit
Base Address registers before the end of frame.
containing the first pixel of the area of interest.
within the 32-bit memory word that contains it.
DMA2DCFG register the address increment between the last word of a line and the first word
of the next line (in number of 32-bit words).
is not activated, the values in the DMA2DCFG register are not considered and the controller
assumes that the displayed area occupies a continuous portion of the memory.
Base word address &
pixel offset
Line-to-line
address increment
Frame Buffer
Displayed Image
6289D–ATARM–3-Oct-11