DF2367VF33 Renesas Electronics America, DF2367VF33 Datasheet - Page 816

• Manufacturer Part Number: DF2367VF33
• Description: MCU 3V 384K 128-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2367VF33

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 33MHz
• Connectivity: I²C, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 84
• Program Memory Size: 384KB (384K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 128-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: HD64F2367VF33; HD64F2367VF33

Section 20 Flash Memory (0.18-μm F-ZTAT Version)
The area that can be executed in the steps of the user procedure program (on-chip RAM, user
MAT, and external space) is shown in section 20.4.4, Procedure Program and Storable Area for
Programming Data.
The following description assumes the area to be programmed on the user MAT is erased and
program data is prepared in the consecutive area. When erasing is not executed, erasing is
executed before writing.
128-byte programming is performed in one program processing. When more than 128-byte
programming is performed, programming destination address/program data parameter is updated
in 128-byte units and programming is repeated.
When less than 128-byte programming is performed, data must total 128 bytes by adding the
invalid data. If the dummy data to be added is H'FF, the program processing period can be
shortened.
1. Select the on-chip program to be downloaded and specify a download destination
2. Program H'A5 in FKEY
3. 1 is written to the SCO bit of FCCS and then download is executed.
Rev.6.00 Mar. 18, 2009 Page 756 of 980
REJ09B0050-0600
When the PPVS bit of FPCS is set to 1, the programming program is selected. Several
programming/erasing programs cannot be selected at one time. If several programs are set,
download is not performed and a download error is returned to the SS bit in DPFR. The start
address of a download destination is specified by FTDAR.
If H'A5 is not written to FKEY for protection, 1 cannot be written to the SCO bit for download
request.
To write 1 to the SCO bit, the following conditions must be satisfied.
⎯ H'A5 is written to FKEY.
⎯ The SCO bit writing is executed in the on-chip RAM.
When the SCO bit is set to 1, download is started automatically. When the SCO bit is returned
to the user procedure program, the SCO is cleared to 0. Therefore, the SCO bit cannot be
confirmed to be 1 in the user procedure program.
The download result can be confirmed only by the return value of DPFR. Before the SCO bit
is set to 1, incorrect determination must be prevented by setting the one byte of the start
address (to be used as DPFR) specified by FTDAR to a value other than the return value
(H'FF).
When download is executed, particular interrupt processing, which is accompanied by the bank
switch as described below, is performed as an internal microcomputer processing. Four NOP
instructions are executed immediately after the instructions that set the SCO bit to 1.
⎯ The user-MAT space is switched to the on-chip program storage area.