8.10.00 J-TRACE ARM Segger Microcontroller Systems, 8.10.00 J-TRACE ARM Datasheet - Page 70
![JTAG EMULATOR ARM7/ARM9 ETM](/photos/9/27/92738/8_10_00-j-trace-arm_sml.jpg)
8.10.00 J-TRACE ARM
Manufacturer Part Number
8.10.00 J-TRACE ARM
Description
JTAG EMULATOR ARM7/ARM9 ETM
Manufacturer
Segger Microcontroller Systems
Type
Emulatorr
Specifications of 8.10.00 J-TRACE ARM
Contents
Emulation Module
For Use With/related Products
ARM7, ARM9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
899-1006
- Current page: 70 of 222
- Download datasheet (3Mb)
70
J-Link / J-Trace (UM08001)
Assigning an IP address manually
If you do not want J-Link to be configured via DHCP, you can assign an IP address
and a subnet mask (optional) manually. This is done via the ipaddr command in
JLink.exe. This command can be used in four different ways, which are explained in
the table below:
Table 3.1: ipaddr command description
Example ipaddr
J-Link>ipaddr
DHCP assigned network configuration
IP-Addr:
Subnetmask: 255.255.0.0
Example ipaddr <IP>
J-Link>ipaddr 192.168.87.115
IP address successfully changed to '192.168.87.115'.
Subnetmask successfully changed to '255.255.0.0'.
Example ipaddr <IP> <Subnet mask>
J-Link>ipaddr 192.168.87.116 255.255.0.0
IP address successfully changed to '192.168.87.116'.
Subnetmask successfully changed to '255.255.0.0'.
Example ipaddr DHCP
J-Link>ipaddr DHCP
Configuration successfully changed to DHCP.
ipaddr
ipaddr <IP>
ipaddr <IP> <Subnet mask>
ipaddr DHCP
Command
192.168.199.29
If no additional parameter is specified, the current
IP and subnet mask of J-Link are shown.
If an IP is given as an additional parameter the
given IP address is set as the IP address for J-Link.
A default 16-bit subnet mask (255.255.0.0) is used.
From this time J-Link uses this static IP, DHCP is
disabled from this point.
If an IP and a subnet mask is given as an additional
parameter, the given IP and the given subnet mask
are used. From this time J-Link uses this static IP
and subnet mask, DHCP is disabled from this point.
If DHCP is given as an additional parameter the use
of DHCP is enabled the next time J-Link boots up.
This especially makes sense if a static IP address
was previously used and now an IP address given
by the DHCP Server shall be used.
CHAPTER 3
© 2004-2011 SEGGER Microcontroller GmbH & Co. KG
Explanation
Setup
Related parts for 8.10.00 J-TRACE ARM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![8.07.00 JTAG ISOLATOR](/photos/8/98/89840/8_07_00-jtag-isolator_tmb.jpg)
Part Number:
Description:
CONNECTOR JTAG-ARM ISOLATION
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.01 J-LINK ARM-14](/photos/9/0/90082/mfg_8_08_01_j-link_arm-14_tmb.jpg)
Part Number:
Description:
ADAPTER ARM TARGET 14PIN RIBBON
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.00 J-LINK ARM](/photos/9/26/92680/8_08_00_j-link_arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.90 J-LINK EDU](/photos/9/27/92725/8_08_90-j-link-edu_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.05.01 FLASHER 5](/photos/9/27/92731/5_05_01-flasher-5_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.04.01 FLASHER ST7](/photos/9/27/92732/5_04_01_flasher_st7_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR ST7 MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.09.01 FLASHER STM 8](/photos/9/27/92733/5_09_01-flasher-stm-8_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR STM8
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.07.01 FLASHER ARM](/photos/9/27/92734/5__07_01_flasher_arm_tmb.jpg)
Part Number:
Description:
PROGRAMMER JTAG FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.12.00 J-LINK ARM-PRO](/photos/9/27/92737/8_12_00-j-link-arm-pro_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR USB ETHERNET ARM
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.13.00 J-TRACE FOR CORTEX-M3](/images/no-image3.png)
Part Number:
Description:
EMULATOR JTAG/SWD CORTEX M3
Manufacturer:
Segger Microcontroller Systems
Datasheet: