8.10.00 J-TRACE ARM Segger Microcontroller Systems, 8.10.00 J-TRACE ARM Datasheet - Page 69
![JTAG EMULATOR ARM7/ARM9 ETM](/photos/9/27/92738/8_10_00-j-trace-arm_sml.jpg)
8.10.00 J-TRACE ARM
Manufacturer Part Number
8.10.00 J-TRACE ARM
Description
JTAG EMULATOR ARM7/ARM9 ETM
Manufacturer
Segger Microcontroller Systems
Type
Emulatorr
Specifications of 8.10.00 J-TRACE ARM
Contents
Emulation Module
For Use With/related Products
ARM7, ARM9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
899-1006
- Current page: 69 of 222
- Download datasheet (3Mb)
3.4.1.2 Connecting via Ethernet only
3.4.2
3.4.2.1 Configuring J-Link via JLink.exe
J-Link / J-Trace (UM08001)
This way of reading out the IP address of J-Link can be used for example if you do
not have administrator rights on the host system in order to install the USB driver
which is necessary to connect to J-Link via USB. To get the IP address which has
been assigned to J-Link via DHCP, you have to read it out from the DHCP IP Assign-
ment table of your DHCP Server:
You can easily identify your J-Link by its host ID (in this case JLINK23) and by its
MAC addr which always starts with: 00-22-C7-01-XX-XX where XX depends on the
serial number of your J-Link. In this case the serial number of the connected J-Link is
23 (0x0017), so its IP address is: 00-22-C7-01-00-17.
By default, J-Link is configured to receive an IP address and a subnet mask via DHCP.
It is also possible to assign a fixed IP address to it. Setting up J-Link can be done via
JLink.exe or via web interface. In the following, both configuration methods are
described.
Configuring J-Link via JLink.exe is very simple because only one command (in dif-
ferent variations) is necessary to choose between automatic IP address and dynamic
IP address assignment.
Note:
your host-system via Ethernet only, you have to type in the ip <IPAddr> command.
Example
ip 192.168.199.29
Assigning an IP address via DHCP
By default, J-Link is configured to acquire an IP address via DHCP, so it should not be
necessary to configure this. But, if you change the IP address to a fixed one, DHCP is
disabled from this point. To re-enable DHCP you should use the ipaddr DHCP com-
mand in JLink.exe. The ipaddr command will be explained in the following.
Configuring the J-Link
If you want to configure J-Link via JLink.exe and J-Link is connected to
© 2004-2011 SEGGER Microcontroller GmbH & Co. KG
69
Related parts for 8.10.00 J-TRACE ARM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![8.07.00 JTAG ISOLATOR](/photos/8/98/89840/8_07_00-jtag-isolator_tmb.jpg)
Part Number:
Description:
CONNECTOR JTAG-ARM ISOLATION
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.01 J-LINK ARM-14](/photos/9/0/90082/mfg_8_08_01_j-link_arm-14_tmb.jpg)
Part Number:
Description:
ADAPTER ARM TARGET 14PIN RIBBON
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.00 J-LINK ARM](/photos/9/26/92680/8_08_00_j-link_arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.90 J-LINK EDU](/photos/9/27/92725/8_08_90-j-link-edu_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.05.01 FLASHER 5](/photos/9/27/92731/5_05_01-flasher-5_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.04.01 FLASHER ST7](/photos/9/27/92732/5_04_01_flasher_st7_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR ST7 MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.09.01 FLASHER STM 8](/photos/9/27/92733/5_09_01-flasher-stm-8_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR STM8
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.07.01 FLASHER ARM](/photos/9/27/92734/5__07_01_flasher_arm_tmb.jpg)
Part Number:
Description:
PROGRAMMER JTAG FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.12.00 J-LINK ARM-PRO](/photos/9/27/92737/8_12_00-j-link-arm-pro_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR USB ETHERNET ARM
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.13.00 J-TRACE FOR CORTEX-M3](/images/no-image3.png)
Part Number:
Description:
EMULATOR JTAG/SWD CORTEX M3
Manufacturer:
Segger Microcontroller Systems
Datasheet: