8.10.00 J-TRACE ARM Segger Microcontroller Systems, 8.10.00 J-TRACE ARM Datasheet - Page 24
![JTAG EMULATOR ARM7/ARM9 ETM](/photos/9/27/92738/8_10_00-j-trace-arm_sml.jpg)
8.10.00 J-TRACE ARM
Manufacturer Part Number
8.10.00 J-TRACE ARM
Description
JTAG EMULATOR ARM7/ARM9 ETM
Manufacturer
Segger Microcontroller Systems
Type
Emulatorr
Specifications of 8.10.00 J-TRACE ARM
Contents
Emulation Module
For Use With/related Products
ARM7, ARM9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
899-1006
- Current page: 24 of 222
- Download datasheet (3Mb)
24
1.3.2
1.3.2.1 Additional features
1.3.2.2 Specifications
J-Link / J-Trace (UM08001)
J-Link is a JTAG emulator designed for ARM cores. It connects
via USB to a PC running Microsoft Windows 2000 or later. For a
complete list of all operating systems which are supported,
please refer to Supported OS on page 21. J-Link has a built-in
20-pin JTAG connector, which is compatible with the standard
20-pin connector defined by ARM.
•
•
•
•
•
•
•
* = Supported since J-Link hardware version 6
** = Measured with J-Link Rev.5, ARM7 @ 50 MHz, 12MHz JTAG
speed.
The following table gives an overview about the specifications (general, mechanical,
electrical) for J-Link ARM. All values are valid for J-Link ARM hardware version 8.
Table 1.1: J-Link ARM specifications
Supported OS
Electromagnetic compatibility (EMC)
Operating temperature
Storage temperature
Relative humidity (non-condensing)
Size (without cables)
Weight (without cables)
USB interface
Target interface
Power supply
Target interface voltage (V
Target supply voltage
Target supply current
Reset Type
Reset low level output voltage (V
Direct download into flash memory of most popular micro-
controllers supported
Full-speed USB 2.0 interface
Serial Wire Debug supported *
Serial Wire Viewer supported *
Download speed up to 720 KBytes/second **
JTAG speed up to 12 MHz
RDI interface available, which allows using J-Link with RDI
compliant software
J-Link ARM
For the whole target voltage range (1.8V <= V
JTAG/SWD Interface, Electrical
IF
)
Available interfaces
OL
CHAPTER 1
)
Mechanical
General
© 2004-2011 SEGGER Microcontroller GmbH & Co. KG
For a complete list of all operating sys-
tems which are supported, please refer
to Supported OS on page 21.
EN 55022, EN 55024
+5°C ... +60°C
-20°C ... +65 °C
Max. 90% rH
100mm x 53mm x 27mm
70g
USB 2.0, full speed
JTAG 20-pin
(14-pin adapter available)
USB powered
Max. 50mA + Target Supply current.
1.2V ... 5V
4.5V ... 5V (if powered with 5V on USB)
Max. 300mA
Open drain. Can be pulled low or
tristated.
V
OL
<= 10% of V
IF
IF
<= 5V)
Introduction
Related parts for 8.10.00 J-TRACE ARM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![8.07.00 JTAG ISOLATOR](/photos/8/98/89840/8_07_00-jtag-isolator_tmb.jpg)
Part Number:
Description:
CONNECTOR JTAG-ARM ISOLATION
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.01 J-LINK ARM-14](/photos/9/0/90082/mfg_8_08_01_j-link_arm-14_tmb.jpg)
Part Number:
Description:
ADAPTER ARM TARGET 14PIN RIBBON
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.00 J-LINK ARM](/photos/9/26/92680/8_08_00_j-link_arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.90 J-LINK EDU](/photos/9/27/92725/8_08_90-j-link-edu_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.05.01 FLASHER 5](/photos/9/27/92731/5_05_01-flasher-5_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.04.01 FLASHER ST7](/photos/9/27/92732/5_04_01_flasher_st7_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR ST7 MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.09.01 FLASHER STM 8](/photos/9/27/92733/5_09_01-flasher-stm-8_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR STM8
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.07.01 FLASHER ARM](/photos/9/27/92734/5__07_01_flasher_arm_tmb.jpg)
Part Number:
Description:
PROGRAMMER JTAG FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.12.00 J-LINK ARM-PRO](/photos/9/27/92737/8_12_00-j-link-arm-pro_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR USB ETHERNET ARM
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.13.00 J-TRACE FOR CORTEX-M3](/images/no-image3.png)
Part Number:
Description:
EMULATOR JTAG/SWD CORTEX M3
Manufacturer:
Segger Microcontroller Systems
Datasheet: