8.10.00 J-TRACE ARM Segger Microcontroller Systems, 8.10.00 J-TRACE ARM Datasheet - Page 176
![JTAG EMULATOR ARM7/ARM9 ETM](/photos/9/27/92738/8_10_00-j-trace-arm_sml.jpg)
8.10.00 J-TRACE ARM
Manufacturer Part Number
8.10.00 J-TRACE ARM
Description
JTAG EMULATOR ARM7/ARM9 ETM
Manufacturer
Segger Microcontroller Systems
Type
Emulatorr
Specifications of 8.10.00 J-TRACE ARM
Contents
Emulation Module
For Use With/related Products
ARM7, ARM9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
899-1006
- Current page: 176 of 222
- Download datasheet (3Mb)
176
8.1.2.1 Target board design
8.1.2.2 Pull-up/pull-down resistors
8.1.2.3 Target power supply
J-Link / J-Trace (UM08001)
* Optional to supply the target board from J-Link.
We strongly advise following the recommendations given by the chip manufacturer.
These recommendations are normally in line with the recommendations given in the
table Pinout for SWD on page 174. In case of doubt you should follow the recommen-
dations given by the semiconductor manufacturer.
A pull-up resistor is required on SWDIO on the target board. ARM recommends 100
kOhms.
In case of doubt you should follow the recommendations given by the semiconductor
manufacturer.
Pin 19 of the connector can be used to supply power to the target hardware. Supply
voltage is 5V, max. current is 300mA. The output current is monitored and protected
against overload and short-circuit.
Power can be controlled via the J-Link commander. The following commands are
available to control power:
Table 8.4: Command List
power on
power off
power on perm
power off perm
J-Link
JTAG connector
Command
Typical target connection for SWD
5V supply
SWDIO
SWCLK
RESET
VTref
SWO
GND
Switch target power on
Switch target power off
Set target power supply default to "on"
Set target power supply default to "off"
15
20
1
7
9
13
19*
CHAPTER 8
© 2004-2011 SEGGER Microcontroller GmbH & Co. KG
19
13
15
20
7
9
1
Explanation
SWDIO
SWCLK
SWO
nRST
Regulator
Voltage
Target board
Target interfaces and adapters
GND
VCC
CPU
VCC
Related parts for 8.10.00 J-TRACE ARM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![8.07.00 JTAG ISOLATOR](/photos/8/98/89840/8_07_00-jtag-isolator_tmb.jpg)
Part Number:
Description:
CONNECTOR JTAG-ARM ISOLATION
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.01 J-LINK ARM-14](/photos/9/0/90082/mfg_8_08_01_j-link_arm-14_tmb.jpg)
Part Number:
Description:
ADAPTER ARM TARGET 14PIN RIBBON
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.00 J-LINK ARM](/photos/9/26/92680/8_08_00_j-link_arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.90 J-LINK EDU](/photos/9/27/92725/8_08_90-j-link-edu_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.05.01 FLASHER 5](/photos/9/27/92731/5_05_01-flasher-5_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.04.01 FLASHER ST7](/photos/9/27/92732/5_04_01_flasher_st7_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR ST7 MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.09.01 FLASHER STM 8](/photos/9/27/92733/5_09_01-flasher-stm-8_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR STM8
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.07.01 FLASHER ARM](/photos/9/27/92734/5__07_01_flasher_arm_tmb.jpg)
Part Number:
Description:
PROGRAMMER JTAG FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.12.00 J-LINK ARM-PRO](/photos/9/27/92737/8_12_00-j-link-arm-pro_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR USB ETHERNET ARM
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.13.00 J-TRACE FOR CORTEX-M3](/images/no-image3.png)
Part Number:
Description:
EMULATOR JTAG/SWD CORTEX M3
Manufacturer:
Segger Microcontroller Systems
Datasheet: