ATAVRSB202 Atmel, ATAVRSB202 Datasheet - Page 53

• Manufacturer Part Number: ATAVRSB202
• Description: KIT BATT MGMT FOR ATMEGA32HVB
• Manufacturer: Atmel

Specifications of ATAVRSB202

• Main Purpose: *
• Embedded: *
• Utilized Ic / Part: *
• Primary Attributes: *
• Secondary Attributes: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8042B–AVR–06/10
Address
0x0000
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
0x0012
0x0014
0x0016
0x0018
0x001A
Labels
Code
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
Table 12-1.
Notes:
If the program never enables an interrupt source, the Interrupt Vectors are not used, and regular
program code can be placed at these locations.
Table 12-2
BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt
Vectors are not used, and regular program code can be placed at these locations. This is also
the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the
Boot section or vice versa.
Table 12-2.
Note:
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega16HVB/32HVB is:
Vector
BOOTRST
No.
27
28
29
RESET
BPINT
VREGMON_INT
EXT_INT0
EXT_INT1
EXT_INT2
EXT_INT3
PCINT0
PCINT1
WDT
BGSCD
CHDET
TIM1_IC
TIM1_COMPA
1
1
0
0
1. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot
2. When the BOOTRST Fuses are programmed, the device will jump to the Boot Loader address
1. The Boot Reset Address is shown in
0x0034
0x0036
0x0038
Flash Section. The address of each Interrupt Vector will then be the address in this table
added to the start address of the Boot Flash Section.
at reset, see
means unprogrammed while “0” means programmed.
Address
shows reset and Interrupt Vectors placement for the various combinations of
Program
Reset and Interrupt Vectors (Continued)
Reset and Interrupt Vectors Placement
(1)
IVSEL
0
1
0
1
”Boot Loader Support – Read-While-Write Self-Programming” on page
Source
CCADC ACC
EE READY
SPM
Comments
; Reset Handler
; Battery Protection Interrupt Handler
; Voltage Regulator Monitor Interrupt Handler
; External Interrupt Request 0 Handler
; External Interrupt Request 1 Handler
; External Interrupt Request 2 Handler
; External Interrupt Request 3 Handler
; Pin Change Interrupt 0 Handler
; Pin Change Interrupt 1 Handler
; Watchdog Time-out Interrupt
; Bandgap Buffer Short Circuit Detected
; Charger Detect
; Timer1 Input Capture Handler
; Timer1 Compare A Handler
Reset Address
0x0000
0x0000
Boot Reset Address
Boot Reset Address
Table 29-5 on page
Interrupt Definition
CC-ADC Accumulate Current Conversion Complete
EEPROM Ready
SPM Ready
ATmega16HVB/32HVB
(1)
Interrupt Vectors Start Address
0x0002
Boot Reset Address + 0x0002
0x0002
Boot Reset Address + 0x0002
204. For the BOOTRST Fuse “1”
191.
53