ATAVRSB202 Atmel, ATAVRSB202 Datasheet - Page 131
ATAVRSB202
Manufacturer Part Number
ATAVRSB202
Description
KIT BATT MGMT FOR ATMEGA32HVB
Manufacturer
Atmel
Specifications of ATAVRSB202
Main Purpose
*
Embedded
*
Utilized Ic / Part
*
Primary Attributes
*
Secondary Attributes
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 131 of 275
- Download datasheet (7Mb)
22.4
22.4.1
8042B–AVR–06/10
Register Description
CHGDCSR – Charger Detect Control and Status Register
•
• Bit 7:5 – Reserved
These bits are reserved and will always read as zero.
• Bit 4 – BATTPVL: BATT pin Voltage Level
BATTPVL will read one as long when the Charger Detect module is enabled and the BATT pin
voltage is above the VPOT level. Otherwise the BATTPVL will read zero.
• Bit 3:2 – CHGDISC[1:0]: Charger Detect Interrupt Sense Control
Edges in the CHARGER_PRESENT signal shown in
vate a Charger Detect Interrupt if the SREG I-flag and the interrupt enable bit in CHGDCSR are
set. By writing the CHGDISC bits to the values shown in
generating interrupt is configured. When changing the CHGDISC bits, an interrupt can occur.
Therefore, it is recommended to first disable the Interrupt by clearing its CHGDIE bit in the
CHGDICSR Register. Finally, the Charger Detect interrupt flag should be cleared by writing a
logical one to CHGDIF bit before the interrupt is re-enabled.
Table 22-1.
• Bit 1 – CHGDIF: Charger Detect Interrupt Flag
Depending on the configuration of the CHGDISC bits in the CHGDCSR, this bit is set when a
charger is either connected or disconnected. The Charger Detect Interrupt is executed if the
CHGDIE bit and the I-bit in SREG are set. This bit is cleared by hardware when executing the
corresponding interrupt handling vector or alternatively by writing a logical one to the CHGDIF. It
is recommended to write this bit to one when setting CHGDIE.
• Bit 0 – CHGDIE: Charger Detect Interrupt Enable
When the CHGDIE bit is set (one), and the I-bit in the Status Register is set (one), the Charger
Detect Interrupt is enabled.
Bit
(0xD4)
Read/Write
Initial Value
When disabling the Charge-FET the Charger Detect module is automatically enabled and a
charger appear to be connected.
CHGISC[1:0]
R
7
–
0
00
01
10
11
Charger Detect Interrupt Sense Control.
R
6
–
0
R
5
–
0
BATTPVL
Detection
Charger Connect
Charger Disconnect
Charger Connect/Disconnect
None
R
4
0
CHGDISC1
R/W
3
0
ATmega16HVB/32HVB
CHGDISC0
Figure 22-1 on page 129
R/W
2
0
Table 22-1 on page 131
CHGDIF
R/W
1
0
CHGDIE
R/W
are used to acti-
0
0
the condition
CHGDCSR
131
Related parts for ATAVRSB202
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: