EVB9311 SMSC, EVB9311 Datasheet - Page 296

• Manufacturer Part Number: EVB9311
• Description: EVALUATION BOARD LAN9311-NU
• Manufacturer: SMSC
• Series: 0133r

Specifications of EVB9311

• Main Purpose: Interface, Ethernet
• Embedded: No
• Utilized Ic / Part: LAN9311
• Primary Attributes: 2 Ports, 100BASE-TX/10BASE-T, Managed
• Secondary Attributes: 2 PHYs with HP Auto-MDIX, Auto- Flow Control, 32-bit CRC, MDI/MDI-X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1076

Revision 1.7 (06-29-10)
autoneg_strap_x
BITS
4:0
autoneg_strap_x
0
0
0
0
1
1
1
1
Selector Field
This field identifies the type of message being sent by Auto-Negotiation.
00001: IEEE 802.3
0
0
1
Note 14.53 The Pause and Asymmetric Pause bits are loaded into the PHY registers by the EEPROM
Note 14.54 The default value of this bit is determined by the Manual Flow Control Enable Strap
Note 14.55 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
Note 14.56 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
Table 14.9 10BASE-T Half Duplex Advertisement Bit Default Value
Table 14.8 10BASE-T Full Duplex Advertisement Default Value
speed_strap_x
Loader.
(manual_FC_strap_x). When the Manual Flow Control Enable Strap is 0, this bit defaults
to 1 (symmetric pause advertised). When the Manual Flow Control Enable Strap is 1, this
bit defaults to 0 (symmetric pause not advertised). Configuration strap values are latched
upon the de-assertion of a chip-level reset as described in
Straps," on page
configuration strap definitions.
(autoneg_strap_x) with the logical AND of the negated speed select strap (speed_strap_x)
and (duplex_strap_x).
strap values are latched upon the de-assertion of a chip-level reset as described in
4.2.4, "Configuration Straps," on page
on page 40
(autoneg_strap_x) and the negated speed strap (speed_strap_x).
default behavior of this bit. Configuration strap values are latched upon the de-assertion
of a chip-level reset as described in
Refer to
definitions.
speed_strap_x
0
0
1
1
0
0
1
1
Section 4.2.4, "Configuration Straps," on page 40
for configuration strap definitions.
0
1
0
DESCRIPTION
40. Refer to
duplex_strap_x
DATASHEET
Table 14.8
0
1
0
1
0
1
0
1
296
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Section 4.2.4, "Configuration Straps," on page 40
defines the default behavior of this bit. Configuration
Default 10BASE-T Half Duplex (Bit 5) Value
Section 4.2.4, "Configuration Straps," on page
40. Refer to
Default 10BASE-T Full Duplex (Bit 6) Value
Section 4.2.4, "Configuration Straps,"
1
0
1
Section 4.2.4, "Configuration
0
1
0
0
1
1
1
1
TYPE
for configuration strap
R/W
SMSC LAN9311/LAN9311i
Table 14.9
DEFAULT
00001b
defines the
Datasheet
Section
40.
for