at91sam9263 ATMEL Corporation, at91sam9263 Datasheet - Page 434
at91sam9263
Manufacturer Part Number
at91sam9263
Description
At91 Arm Thumb Microcontrollers
Manufacturer
ATMEL Corporation
Datasheet
1.AT91SAM9263.pdf
(1065 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
at91sam9263-CJ
Manufacturer:
ATMEL
Quantity:
181
Company:
Part Number:
at91sam9263-EK
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
at91sam9263B-CU
Manufacturer:
IDT
Quantity:
1 043
Part Number:
at91sam9263B-CU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
at91sam9263B-CU-100
Manufacturer:
ATMEL
Quantity:
1 000
- Current page: 434 of 1065
- Download datasheet (16Mb)
Figure 30-5. Input Glitch Filter Timing
30.4.10
Figure 30-6. Input Change Interrupt Timings
434
if PIO_IFSR = 0
if PIO_IFSR = 1
Read PIO_ISR
PIO_PDSR
PIO_PDSR
Pin Level
Pin Level
PIO_ISR
AT91SAM9263 Preliminary
MCK
Input Change Interrupt
MCK
The PIO Controller can be programmed to generate an interrupt when it detects an input change
on an I/O line. The Input Change Interrupt is controlled by writing PIO_IER (Interrupt Enable
Register) and PIO_IDR (Interrupt Disable Register), which respectively enable and disable the
input change interrupt by setting and clearing the corresponding bit in PIO_IMR (Interrupt Mask
Register). As Input change detection is possible only by comparing two successive samplings of
the input of the I/O line, the PIO Controller clock must be enabled. The Input Change Interrupt is
available, regardless of the configuration of the I/O line, i.e. configured as an input only, con-
trolled by the PIO Controller or assigned to a peripheral function.
When an input change is detected on an I/O line, the corresponding bit in PIO_ISR (Interrupt
Status Register) is set. If the corresponding bit in PIO_IMR is set, the PIO Controller interrupt
line is asserted. The interrupt signals of the thirty-two channels are ORed-wired together to gen-
erate a single interrupt signal to the Advanced Interrupt Controller.
When the software reads PIO_ISR, all the interrupts are automatically cleared. This signifies that
all the interrupts that are pending when PIO_ISR is read must be handled.
1 cycle
1 cycle
APB Access
up to 1.5 cycles
1 cycle
up to 2.5 cycles
2 cycles
APB Access
6249D–ATARM–20-Dec-07
up to 2 cycles
1 cycle
1 cycle
Related parts for at91sam9263
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
At91sam Arm-based Flash Mcu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Flash Mcu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM THUMB-BASED MICROCONTROLLERS
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 MEMORY EXTENSION CARD
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
AT91 ARM X40 SERIES EVAL KIT
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
AT91 ARM Cortex M3-based Processor
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet: