DS3112+W Maxim Integrated Products, DS3112+W Datasheet - Page 51

• Manufacturer Part Number: DS3112+W
• Description: IC MUX T3/E3 3.3V 256-PBGA
• Manufacturer: Maxim Integrated Products

Specifications of DS3112+W

• Controller Type: Framer, Multiplexer
• Interface: Parallel/Serial
• Voltage - Supply: 3.135 V ~ 3.465 V
• Current - Supply: 150mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 256-PBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit #
Name
Default
Bit 0: BiPolar Violation Insert (BPVI). A zero to one transition on this bit will cause a single BPV to be inserted
into the transmit data stream. Once this bit has been toggled from a 0 to a 1, the device waits for the next
occurrence of three consecutive ones to insert the BPV. This bit must be cleared and set again for a subsequent
error to be inserted. Toggling this bit has no affect when the T3/E3 interface is in the Unipolar Mode (Section
for details about the Unipolar Mode). In the manual error insert mode (MEIMS = 1), errors will be inserted on each
toggle of the FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 1: Excessive Zero Insert (EXZI). A zero to one transition on this bit will cause a single EXZ event to be
inserted into the transmit data stream. An EXZ event is defined as three or more consecutive zeros in the T3 mode
and four or more consecutive zeros in the E3 mode. Once this bit has been toggled from a zero to a one, the device
waits for the next possible B3ZS/HDB3 codeword insertion and it suppresses that codeword from being inserted
and hence this creates the EXZ event. This bit must be cleared and set again for a subsequent error to be inserted.
Toggling this bit has no affect when the T3/E3 interface is in the Unipolar Mode (Section 4.2 for details about the
Unipolar Mode). In the Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the
FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 2: T3 Parity Bit Error Insert (T3PBEI). A zero to one transition on this bit will cause a single T3 parity error
event to be inserted into the transmit data stream. A T3 parity event is defined as flipping the proper polarity of
both the P bits in a T3 Frame. (See Section
zero to a one, the device waits for the next T3 frame to flip both P bits. This bit must be cleared and set again for a
subsequent error to be inserted. Toggling this bit has no affect when the device is operated in the E3 mode. In the
Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the FTMEI input signal as long
as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 3: T3 C-Bit Parity Error Insert (T3CPBEI). A zero to one transition on this bit will cause a single T3 C-Bit
parity error event to be inserted into the transmit data stream. A T3 parity event is defined as flipping the proper
polarity of all three CP bits in a T3 Frame. (See Section
toggled from a zero to a one, the device waits for the next T3 frame to flip the three CP bits. This bit must be
cleared and set again for a subsequent error to be inserted. Toggling this bit has no affect when the T3 framer is not
operated in the C-Bit parity mode (See Section
operated in the E3 mode. In the Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of
the FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 4: Frame Bit Error Insert (FBEI). A zero to one transition on this bit will cause the transmit framer to
generate framing bit errors. The type of framing bit errors inserted is controlled by the FBEIC0 and FBEIC1 bits
(see discussion below). Once this bit has been toggled from a 0 to a 1, the device waits for the next possible
framing bit to insert the errors. This bit must be cleared and set again for a subsequent error to be inserted. In the
Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the FTMEI input signal as long
as this bit is set high. When this bit is set low, no errors will be inserted.
MEIMS
15
—
—
7
0
FBEIC1
14
—
—
6
0
T3E3EIC
T3/E3 Error Insert Control Register
18h
FBEIC0
13
—
—
5
0
14.5
14.7
for details about the P bits.) Once this bit has been toggled from a
for details about the C-Bit Parity mode.) or when the device is
51 of 133
FBEI
12
—
—
4
0
14.7
for details about the CP bits.) Once this bit has been
T3CPBEI
11
—
—
3
0
T3PBEI
10
—
—
2
0
EXZI
—
—
1
9
0
BPVI
—
—
DS3112
0
0
8
4.2