EP9302-CQZ Cirrus Logic Inc, EP9302-CQZ Datasheet - Page 644

• Manufacturer Part Number: EP9302-CQZ
• Description: IC ARM9 SOC PROCESSOR 208LQFP
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9302-CQZ

• Program Memory Type: ROMless
• Package / Case: 208-LQFP
• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 19
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 5x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• Data Ram Size: 16 bit
• Interface Type: USB, USART, SPI
• Maximum Clock Frequency: 200 MHz
• Number Of Programmable I/os: 37
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9302A-Z
• Controller Family/series: (ARM9)
• No. Of I/o's: 19
• Ram Memory Size: 16MB
• Cpu Speed: 200MHz
• No. Of Timers: 4
• Embedded Interface Type: AC97, I2S, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1132 - KIT DEVELOPMENT EP9302 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1137

19
19-2
Watchdog Timer
EP93xx User’s Guide
19.1.1 Watchdog Activation
19.1.2 Clocking Requirements
19.1.3 Reset Requirements
19.1.4 Watchdog Status
The Watchdog circuitry may be disabled via software for test purposes on products that do
not wish to use a Watchdog timer by writing 0xAA55 to the Watchdog register. The Watchdog
may also be re-enabled via software by writing 0xAAAA to the Watchdog register.
The Watchdog circuitry may be disabled via hardware on products that do not need to use a
Watchdog timer, by applying an external pull down on the CSn[1]
(HW_WATCHDOG_DISABLEn) signal during reset. This will allow the block to detect the
presence of the resistor during the bus reset (HRESETn low) and disable the counter. During
reset, the chip will disable the output driver and provide a weak pull-up resistor on this pad.
The WATCHDOG_CLK for stepping the counter in the Watchdog has a frequency that is
nominally 256 Hz, for generating a 250 ms time-out and a 250 ms reset pulse duration.
The Watchdog block has the following four reset inputs:
The Watchdog timer register can be read to determine the cause of a reset. The register
contains user reset status (external reset on RSTOn), three-key reset status from the key
scan controller, and Watchdog reset status bits (reset caused by WATCHDOG_RESETn).
The state of these bits determines if the reset condition was the result of a user reset, a three-
key reset, a power on reset, or a watch dog time-out. The status of these bits can only be
cleared by a power on reset (internal chip voltage detect power on signal PWR_RESETn). An
additional 7-bit status register is provided in the Watchdog module as WDSTAT. This status
value is held through all resets but power on reset. The system can be reset by a three-key
reset, a user reset, or a Watchdog reset without losing the contents of this register.
• HRESETn: This is the AHB bus reset signal from the Syscon block, which includes a
• USR_RESETn: This is the external user reset input, and its status is kept in register
• PWR_RESETn: This is the power-on-reset input for resetting everything including reset
• RESET_KEYS_DETECTED: The Watchdog will time out if the three-key reset signal
software reset.
Watchdog[2].
status bits. The power-on-reset is generated by a combination of the external PRSTn pin
and the on chip voltage monitor/power up detector.
from the key scanning controller is activated. This input disables the ability to reset the
Watchdog. If the Watchdog is hardware or software disabled, detection of the three-key
reset will over-ride the Watchdog counter disable and cause the circuit to time out and
generate the WATCHDOG_RESETn output anyway. It behaves as a USR_RESETn
signal.
Copyright 2007 Cirrus Logic
DS785UM1