TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 469

• Manufacturer Part Number: TMPM330FWFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
• Manufacturer: Toshiba

Specifications of TMPM330FWFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 128K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

17.2.10
Note:
offers these four commands, of which the details are provided on the following subsections.
If a password is set to 0xFF (erased data), it is difficult to protect data securely due to an easy-to-guess
password. Even if Single Boot mode is not used, it is recommended to set a unique value as a password.
When Single Boot mode is selected, the boot program is automatically executed on startup. The boot program
Operation of Boot Program
1. RAM Transfer command
2. Show Flash Memory SUM command
3. Show Product Information command
4. Chip and Protection Bit Erase command
RAM and executes the program once the transfer is successfully completed. The user program RAM
space can be assigned to the range from 0x2000_0400 to the end address of RAM, whereas the boot
program area (0x2000_0000 ~ 0x2000_03FF) is unavailable. The user program starts at the assigned
RAM address.
this provides the ability to control on-board programming of the flash memory in a unique manner. The
programming routine must utilize the flash memory command sequences described in Section 17.3.
Before initiating a transfer, the RAM Transfer command verifies a password sequence coming from
the controller against that stored in the flash memory.
boot program does not provide a command to read out the contents of the flash memory. Instead, the
Flash Memory SUM command can be used for software revision management.
and the like. This command also reads out the contents of the flash memory locations at addresses
shown below. In addition to the Show Flash Memory Sum command, these locations can be used for
software revision management.
All the blocks in the memory cell and their protection conditions are erased even when any of the blocks
are prohibited from writing and erasing. When the command is completed, the FCSECBIT <SECBIT>
bit is set to "1". This command serves to recover boot programming operation when a user forgets the
password. Therefore password verification is not executed.
The RAM Transfer command stores program code transferred from a host controller to the on-chip
The RAM Transfer command can be used to download a flash programming routine of your own;
The Show Flash Memory SUM command adds the entire contents of the flash memory together. The
The Show Product Information command provides the product name, on-chip memory configuration
This command erases the entire area of the flash memory automatically without verifying a password.
TMPM330FWFG
TMPM330FDFG
TMPM330FYFG
Product name
Page 449
0x3F87_FF00 to 0x3F87_FF03
0x3F81_FF00 to 0x3F81_FF03
Area
TMPM330FDFG/FYFG/FWFG