TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 148

• Manufacturer Part Number: TMPM330FWFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
• Manufacturer: Toshiba

Specifications of TMPM330FWFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 128K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

8.2
Port functions
8.2.6
Type
8.2.6.1
8.2.6.2
units of bits. Besides the general-purpose port function, the port F performs the functions of the serial interface,
the remote control signal preprocessor, the serial bus interface and the external interrupt input.
corresponding bit of the two registers. If you use the port F as other than a general-purpose port, set "1" to the
corresponding bit of the function register. Do not set "1" to the both function registers at the same time.
in the PFIE register.
is set to stop driving of pins during STOP mode.
Port F data register
Port F output control register
Port F function register 1
Port F function register 2
Port F open drain control register
Port F pull-up control register
Port F input control register
Port F (PF0 to PF7)
The port F is a general-purpose, 8-bit input/output port. For this port, inputs and outputs can be specified in
Reset initializes all bits of the port F as general-purpose ports with input, output and pull-up disabled.
The port F has two types of function register. If you use the port F as a general-purpose port, set "0" to the
To use the external interrupt input for releasing STOP mode, select this function in the PFFR1 and enable input
These settings enable the interrupt input even if the CGSTBYCR<DRVE> bit in the clock/mode control block
Note:In modes other than STOP mode, interrupt input is enabled regardless of the PFFR register setting if
Port F Circuit Type
Port F Register
input is enabled in PxIE. Make sure to disable unused interrupts when programming the device.
T8
7
T13
6
Register name
T13
5
Page 128
T13
4
PFDATA
PFFR1
PFFR2
PFPUP
PFCR
PFOD
PFIE
T4
3
T16
Base Address = 0x4000_0140
2
TMPM330FDFG/FYFG/FWFG
Address (Base+)
0x000C
0x002C
0x0000
0x0004
0x0008
0x0028
0x0038
T4
1
T10
0