PIC18F4580-I/P Microchip Technology Inc., PIC18F4580-I/P Datasheet - Page 23

• Manufacturer Part Number: PIC18F4580-I/P
• Description: 40 PIN, 32 KB FLASH, 1536 RAM, 36 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4580-I/P

• A/d Inputs: 11-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 36
• Interface: CAN/I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Ram Size: 1.5K Bytes
• Speed: 40 MHz
• Timers: 1-8 bit, 3-16 bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

2.6.2
The PIC18FXX8 devices contain circuitry to prevent
“glitches” when switching between oscillator sources.
Essentially, the circuitry waits for eight rising edges of
the clock source that the processor is switching to. This
ensures that the new clock source is stable and that its
pulse width will not be less than the shortest pulse
width of the two clock sources.
Figure 2-7 shows a timing diagram indicating the tran-
sition from the main oscillator to the Timer1 oscillator.
The Timer1 oscillator is assumed to be running all the
time. After the SCS bit is set, the processor is frozen at
the next occurring Q1 cycle. After eight synchronization
cycles are counted from the Timer1 oscillator,
operation resumes. No additional delays are required
after the synchronization cycles.
FIGURE 2-7:
FIGURE 2-8:
 2004 Microchip Technology Inc.
Internal System
(OSCCON<0>)
Note 1: T
T1OSI
OSC1
Internal
System
Clock
SCS
(OSCCON<0>)
Program
Counter
Note 1: Delay on internal system clock is eight oscillator cycles for synchronization.
Program
Counter
T1OSI
OSC1
OSC2
Clock
SCS
OST
OSCILLATOR TRANSITIONS
Q1
= 1024 T
T
OSC
Q2
Q3
PC
Q3
PC
OSC
Q4
TIMING DIAGRAM FOR TRANSITION FROM OSC1 TO TIMER1 OSCILLATOR
TIMING DIAGRAM FOR TRANSITION BETWEEN TIMER1 AND OSC1 (HS, XT, LP)
(drawing not to scale).
Q4
Q1
T
DLY
1
Q1
T
2
T
1
P
3
T
4
OST
Tscs
PC + 2
5
T
OSC
6
PC + 2
7
The sequence of events that takes place when switch-
ing from the Timer1 oscillator to the main oscillator will
depend on the mode of the main oscillator. In addition
to eight clock cycles of the main oscillator, additional
delays may take place.
If the main oscillator is configured for an external
crystal (HS, XT, LP), the transition will take place after
an oscillator start-up time (T
diagram indicating the transition from the Timer1
oscillator to the main oscillator for HS, XT and LP
modes is shown in Figure 2-8.
1
8
2
Q1
3
Q2
4
T
T
SCS
T
1
5
Q3
P
6
Q4
7
PIC18FXX8
OST
Q1 Q2 Q3 Q4 Q1 Q2
Q1
8
) has occurred. A timing
Q2
PC + 4
DS41159D-page 21
Q3
Q4
PC + 4
Q1
Q3