HD6417750RF240DV Renesas Electronics America, HD6417750RF240DV Datasheet - Page 738

• Manufacturer Part Number: HD6417750RF240DV
• Description: MPU 3V 16K I-TEMP,PB-FREE 208-QF
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7750r

Specifications of HD6417750RF240DV

• Core Processor: SH-4
• Core Size: 32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, FIFO, SCI, SmartCard
• Peripherals: DMA, POR, WDT
• Number Of I /o: 28
• Program Memory Type: ROMless
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.4 V ~ 1.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-QFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

Section 14 Direct Memory Access Controller (DMAC)
14.9
1. When modifying SAR0–SAR3, DAR0–DAR3, DMATCR0–DMATCR3, and CHCR0–
2. The NMIF bit in DMAOR is set when an NMI interrupt is input even if the DMAC is not
3. Check that DMA transfer is not in progress before making a transition to the module standby
4. Do not specify a DMAC, CCN, BSC, or UBC control register as the DMAC transfer source or
5. When activating the DMAC, make the SAR, DAR, and DMATCR register settings for the
6. After the DMATCR count reaches 0 and DMA transfer ends normally, always write 0 to
Rev.7.00 Oct. 10, 2008 Page 652 of 1074
REJ09B0366-0700
CHCR3 in the SH7750 or SH7750S or when modifying SAR0–SAR7, DAR0–DAR7,
DMATCR0–DMATCR7, and CHCR0–CHCR7 in the SH7750R, first clear the DE bit for the
relevant channel.
operating.
Confirmation method when DMA transfer is not executed correctly:
With the SH7750 and SH7750S, read the NMIF, AE, and DME bits in DMAOR, the DE and
TE bits in CHCR0–CHCR3, and DMATCR0–DMATCR3. With the SH7750R, read the
NMIF, AE, and DME bits in DMAOR, the DE and TE bits in CHCR0–CHCR7, and
DMATCR0–DMATCR7. If NMIF was set before the transfer, the DMATCR transfer count
will remain at the set value. If NMIF was set during the transfer, when the DE bit is 1 and the
TE bit is 0 in CHCR0–CHCR3 in the SH7750 or SH7750S or CHCR0–CHCR7 in the
SH7750R, the DMATCR value will indicate the remaining number of transfers.
Also, the next addresses to be accessed can be found by reading SAR0–SAR3 and DAR0–
DAR3 in the SH7750 or SH7750S or SAR0–SAR7 and DAR0–DAR7 in the SH7750R. If the
AE bit has been set, an address error has occurred. Check the set values in CHCR, SAR, and
DAR.
state, standby mode, or deep sleep mode.
Either check that TE = 1 in the SH7750 or SH7750S's CHCR0–CHCR3 or in the SH7750R's
CHCR0–CHCR7, or clear DME to 0 in DMAOR to terminate DMA transfer. When DME is
cleared to 0 in DMAOR, transfer halts at the end of the currently executing DMA bus cycle.
Note, therefore, that transfer may not end immediately, depending on the transfer data size.
DMA operation is not guaranteed if the module standby state, standby mode, or deep sleep
mode is entered without confirming that DMA transfer has ended.
destination.
relevant channel before setting DE to 1 in CHCR, or make the register settings with DE
cleared to 0 in CHCR, then set DE to 1. It does not matter whether setting of the DME bit to 1
in DMAOR is carried out first or last. To operate the relevant channel, DME and DE must both
be set to 1. The DMAC may not operate normally if the SAR, DAR, and DMATCR settings
are not made (with the exception of the unused register in single address mode).
DMATCR even when executing the maximum number of transfers on the same channel.
Usage Notes