AT91SAM7S256D-AU Atmel, AT91SAM7S256D-AU Datasheet - Page 517
AT91SAM7S256D-AU
Manufacturer Part Number
AT91SAM7S256D-AU
Description
ARM Microcontrollers - MCU 256K Flash SRAM 64K ARM based MCU
Manufacturer
Atmel
Series
SAM7S256r
Datasheet
1.AT91SAM7S256D-AU.pdf
(775 pages)
Specifications of AT91SAM7S256D-AU
Rohs
yes
Core
ARM
Processor Series
AT91SAM
Data Bus Width
16 bit/32 bit
Maximum Clock Frequency
55 MHz
Program Memory Size
256 KB
Data Ram Size
64 KB
On-chip Adc
Yes
Operating Supply Voltage
3 V to 3.6 V
Operating Temperature Range
- 40 C to + 85 C
Package / Case
LQFP-64
Mounting Style
SMD/SMT
Interface Type
2-Wire, I2S, SPI, USART
Length
7 mm
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT91SAM7S256D-AU
Manufacturer:
ATMEL
Quantity:
101
- Current page: 517 of 775
- Download datasheet (5Mb)
35.5.3.7
35.5.3.8
Warning: Read, write operations to the UDP registers are allowed only if MCK is enabled for the UDP peripheral.
Switching off MCK for the UDP peripheral must be one of the last operations after writing to the and acknowledg-
ing the RXSUSP.
In suspend mode, a resume event on the USB bus line is detected asynchronously, transceiver and clocks are dis-
abled (however the pullup shall not be removed).
Once the resume is detected on the bus, the WAKEUP signal in the UDP_ISR is set. It may generate an interrupt if
the corresponding bit in the UDP_IMR register is set. This interrupt may be used to wake up the core, enable PLL
and main oscillators and configure clocks.
Warning: Read, write operations to the UDP registers are allowed only if MCK is enabled for the UDP peripheral.
MCK for the UDP must be enabled before clearing the WAKEUP bit in the UDP_ICR register and clearing TXVDIS
in the UDP_TXVC register.
In Suspend state it is possible to wake up the host sending an external resume.
To force a K state to the bus (DM at 3.3V and DP tied to GND), it is possible to use a transistor to connect a pullup
on DM. The K state is obtained by disabling the pullup on DP and enabling the pullup on DM. This should be under
the control of the application.
Figure 35-15. Board Schematic to Drive a K State
• The device must wait at least 5 ms after being entered in suspend before sending an external resume.
• The device has 10 ms from the moment it starts to drain current and it forces a K state to resume the host.
• The device must force a K state from 1 to 15 ms to resume the host
Receiving a Host Resume
Sending a Device Remote Wakeup
PIO
0: Force Wake UP (K State)
1: Normal Mode
SAM7S Series [DATASHEET]
DM
3V3
6175M–ATARM–26-Oct-12
1.5 K
517
Related parts for AT91SAM7S256D-AU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVAL FOR ARM AT91SAM7S
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools KICKSTART KIT ATMEL AT91SAM7S
Manufacturer:
IAR Systems
Part Number:
Description:
MCU ARM9 64K SRAM 144-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU FLASH 256K 100LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MPU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM9 ULTRA LOW PWR 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM9 324-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU ARM9 SAMPLING 217CBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 217-LFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 208-PQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM 512K HS FLASH 100-LQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ARM 512K HS FLASH 100-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM9 MCU 200 MHZ 324-TFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM MCU 16BIT 128K 256BGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC ARM7 MCU 32BIT 128K 64LQFP
Manufacturer:
Atmel
Datasheet: