AT91SAM7S256D-AU Atmel, AT91SAM7S256D-AU Datasheet - Page 111

• Manufacturer Part Number: AT91SAM7S256D-AU
• Description: ARM Microcontrollers - MCU 256K Flash SRAM 64K ARM based MCU
• Manufacturer: Atmel
• Series: SAM7S256r

Specifications of AT91SAM7S256D-AU

• Rohs: yes
• Core: ARM
• Processor Series: AT91SAM
• Data Bus Width: 16 bit/32 bit
• Maximum Clock Frequency: 55 MHz
• Program Memory Size: 256 KB
• Data Ram Size: 64 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3 V to 3.6 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: LQFP-64
• Mounting Style: SMD/SMT
• Interface Type: 2-Wire, I2S, SPI, USART
• Length: 7 mm

Figure 19-6. Example of Partial Page Programming
19.2.4.2
16 words
16 words
16 words
16 words
The Partial Programming mode works only with 32-bit (or higher) boundaries. It cannot be used with boundaries
lower than 32 bits (8 or 16-bit for example).
After programming, the page (the whole lock region) can be locked to prevent miscellaneous write or erase
sequences. The lock bit can be automatically set after page programming using WPL.
Data to be written are stored in an internal latch buffer. The size of the latch buffer corresponds to the page size.
The latch buffer wraps around within the internal memory area address space and appears to be repeated by the
number of pages in it.
Note:
Data are written to the latch buffer before the programming command is written to the Flash Command Register
MC_FCR. The sequence is as follows:
Two errors can be detected in the MC_FSR register after a programming sequence:
The entire memory can be erased if the Erase All Command (EA) in the Flash Command Register MC_FCR is
written.
Erase All operation is allowed only if there are no lock bits set. Thus, if at least one lock region is locked, the bit
LOCKE in MC_FSR rises and the command is cancelled. If the bit LOCKE has been written at 1 in MC_FMR, the
interrupt line rises.
• Write the full page, at any page address, within the internal memory area address space using only 32-bit
• Programming starts as soon as the page number and the programming command are written to the Flash
• When programming is completed, the bit FRDY in the Flash Programming Status Register (MC_FSR) rises. If
• Programming Error: A bad keyword and/or an invalid command have been written in the MC_FCR register.
• Lock Error: The page to be programmed belongs to a locked region. A command must be previously run to
access.
Command Register. The FRDY bit in the Flash Programming Status Register (MC_FSR) is automatically
cleared.
an interrupt was enabled by setting the bit FRDY in MC_FMR, the interrupt line of the Memory Controller is
activated.
unlock the corresponding region.
Erase All Command
Writing of 8-bit and 16-bit data is not allowed and may lead to unpredictable data corruption.
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
Erase All Flash
Page 7 erased
32 bits wide
Step 1.
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
...
...
...
...
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
Programming of the second part of Page 7
FF
FF
FF
CA FE
CA FE
CA FE
FF
FF
FF
FF
FF
FF
(NEBP = 1)
32 bits wide
FF
FF
FF
FF
FF
FF
FF
FF
FF
Step 2.
...
...
...
...
CA
CA
CA
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FE
FE
FE
FF
FF
FF
FF
FF
FF
Programming of the third part of Page 7
SAM7S Series [DATASHEET]
FF
FF
FF
CA FE
CA FE
CA FE
DE CA
DE CA
DE CA
FF
FF
FF
(NEBP = 1)
32 bits wide
6175M–ATARM–26-Oct-12
FF
FF
FF
FF
FF
FF
Step 3.
...
...
...
...
CA
CA
CA
FF
FF
FF
DE CA
DE CA
DE CA
FF
FF
FF
FF
FF
FF
FE
FE
FE
FF
FF
FF
111