SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 919

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 41-9. Disabling Low-power Mode
41.8
41.8.1
11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11
Functional Description
(CAN_MSRx)
CAN Controller Initialization
(CAN_SR)
WAKEUP
(CAN_MR)
(CAN_SR)
CAN BUS
SLEEP
MRDY
LPM
Depending on the corresponding mask in the CAN_IMR register, an interrupt is generated while
WAKEUP is set. The SLEEP signal in the CAN_SR register is automatically cleared once
WAKEUP is set. WAKEUP signal is automatically cleared once SLEEP is set.
If no message is being sent on the bus, then the CAN controller is able to send a message
eleven bit times after disabling Low-power Mode.
If there is bus activity when Low-power mode is disabled, the CAN controller is synchronized
with the bus activity in the next interframe. The previous message is lost (see
After power-up reset, the CAN controller is disabled. The CAN controller clock must be activated
by the Power Management Controller (PMC) and the CAN controller interrupt line must be
enabled by the interrupt controller (AIC).
The CAN controller must be initialized with the CAN network parameters. The CAN_BR register
defines the sampling point in the bit time period. CAN_BR must be set before the CAN controller
is enabled by setting the CANEN field in the CAN_MR register.
The CAN controller is enabled by setting the CANEN flag in the CAN_MR register. At this stage,
the internal CAN controller state machine is reset, error counters are reset to 0, error flags are
reset to 0.
Once the CAN controller is enabled, bus synchronization is done automatically by scanning
eleven recessive bits. The WAKEUP bit in the CAN_SR register is automatically set to 1 when
the CAN controller is synchronized (WAKEUP and SLEEP are stuck at 0 after a reset).
The CAN controller can start listening to the network in Autobaud Mode. In this case, the error
counters are locked and a mailbox may be configured in Receive Mode. By scanning error flags,
the CAN_BR register values synchronized with the network. Once no error has been detected,
the application disables the Autobaud Mode, clearing the ABM field in the CAN_MR register.
Message lost
Interframe synchronization
Bus Activity Detected
Message x
SAM9X25
SAM9X25
Figure
41-9).
919
919