SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 843

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.7.8.13
Figure 39-44. Frame Slot Mode
11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11
TXRDY
Write
US_LINID
Write
US_THR
LINTC
Break
Frame Slot Mode
Header
Synch
This mode is useful only for Master nodes. It respects the following rule: each frame slot shall be
longer than or equal to TFrame_Maximum.
If the Frame Slot Mode is enabled (FSDIS = 0) and a frame transfer has been completed, the
TXRDY flag is set again only after TFrame_Maximum delay, from the start of frame. So the Mas-
ter node cannot send a new header if the frame slot duration of the previous frame is inferior to
TFrame_Maximum.
If the Frame Slot Mode is disabled (FSDIS = 1) and a frame transfer has been completed, the
TXRDY flag is set again immediately.
The TFrame_Maximum is calculated as below:
If the Checksum is sent (CHKDIS = 0):
If the Checksum is not sent (CHKDIS = 1):
Note:
• THeader_Nominal = 34 x Tbit
• TResponse_Nominal = 10 x (NData + 1) x Tbit
• TFrame_Maximum = 1.4 x (THeader_Nominal + TResponse_Nominal + 1)
• TFrame_Maximum = 1.4 x (34 + 10 x (DLC + 1 + 1) + 1) x Tbit
• TFrame_Maximum = (77 + 14 x DLC) x Tbit
• THeader_Nominal = 34 x Tbit
• TResponse_Nominal = 10 x NData x Tbit
• TFrame_Maximum = 1.4 x (THeader_Nominal + TResponse_Nominal + 1
• TFrame_Maximum = 1.4 x (34 + 10 x (DLC + 1) + 1) x Tbit
• TFrame_Maximum = (63 + 14 x DLC) x Tbit
Data 1
The term “+1” leads to an integer result for TFrame_Max (LIN Specification 1.3)
Protected
Identifier
Data3
Frame slot = TFrame_Maximum
Response
space
Data 2
Frame
Data 1
Data 3
Data N
Response
Data N-1
Data N
Frame Slot Mode
Checksum
Disabled
(Note:)
SAM9X25
SAM9X25
(Note:)
)
Frame Slot Mode
frame
space
Inter-
Enabled
843
843